Help
Require Assistance? Read the Beginners Guide to RouterForums.com
RouterForums.com - Router and Woodworking Discussion Community

Go Back   Router Forums > Routers > General Routing
IconIt appears you arenít a registered member of the Router Forums community. Why not spend less than a minute and register for the oldest and largest router and woodworking community on the web! Join in over 29,500 discussions with over 65,000 woodworkers. If youíre an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account!

Sanding question

This is a discussion on Sanding question within the General Routing forums, part of the Routers category; Originally Posted by bobj3 Hi Danny Very nice, looks you have been out shopping for ...


  • Replies: 18, Views: 1648

New Reply
 
LinkBack Thread Tools Display Modes
Old 11-20-2010, 08:37 PM   #11 (permalink)
Registered User
 
Join Date: Jun 2009
Country: United States
First Name: Danny
Posts: 523
jd99 is on a distinguished road

Default
Report Post Report This Post!

Quote:
Originally Posted by bobj3 View Post
Hi Danny

Very nice, looks you have been out shopping for some Xmax. templates .

Eagle or Woodcraft ?

=======
bought them from Eagle, I started with the chip tray, and the christmas tree, then I made the mistake of showing the other holiday trays to the better half, now I got a honey do list of christmas gifts for just about every one they have. The only one she didn't like was the santa hat.

Gives me the templates to make them way ahead of time next year I guess.

jd99 is offline  
Sponsored Advertisement - Register now to remove this advertisement.
** Please be sure to read our Disclaimer at the bottom of the page. **
These advertisements are only displayed to guests, register now for your FREE account on the worlds largest router and woodworking community!
Old 11-20-2010, 09:01 PM   #12 (permalink)
Forum Contributor
 
Join Date: Jan 2006
Country: United States
First Name: Bj
Posts: 23,793
bobj3 has a brilliant futurebobj3 has a brilliant futurebobj3 has a brilliant futurebobj3 has a brilliant future

Default
Report Post Report This Post!

Thanks Danny

I know this is not high tech but it works for me,,sanding sponge, I cut out a cir. out of them and super glue them to a wooden down rod.

Amazon.com: sanding sponge Home Improvement

=========
Quote:
Originally Posted by jd99 View Post
bought them from Eagle, I started with the chip tray, and the christmas tree, then I made the mistake of showing the other holiday trays to the better half, now I got a honey do list of christmas gifts for just about every one they have. The only one she didn't like was the santa hat.

Gives me the templates to make them way ahead of time next year I guess.
__________________
"It's fine to disagree with other members as long as you respect their opinions"

Marc Sommerfeld Tools ,Videos
http://www.youtube.com/channel/UCT-n...RWaEpMA/videos

Find all threads started by bobj3
http://www.routerforums.com/search.php?searchid=944097


bobj3 is offline  
Old 11-22-2010, 09:03 AM   #13 (permalink)
Registered User
 
Join Date: Feb 2009
Country: United States
First Name: Charley
Posts: 608
CharleyL is on a distinguished road

Default
Report Post Report This Post!

This sounds like a good excuse to buy more tools.
Have you seen these? The inflatable sanding heads come in small sizes and are great for sanding those curved tight spots.
King Arthur Tools
Woodcraft and Klingspor sell them.

CharleyL
CharleyL is offline  
Old 11-22-2010, 09:27 AM   #14 (permalink)
Registered User
 
Join Date: Jun 2009
Country: United States
First Name: Danny
Posts: 523
jd99 is on a distinguished road

Default
Report Post Report This Post!

Quote:
Originally Posted by CharleyL View Post
This sounds like a good excuse to buy more tools.
Have you seen these? The inflatable sanding heads come in small sizes and are great for sanding those curved tight spots.
King Arthur Tools
Woodcraft and Klingspor sell them.

CharleyL
That's intersting, I almost was ready to add to cart then I noticed the round head is 2" in Dia. thats too big I need it to be less then 1 1/4" Dia.

If i can get the things cut with out any burning then sanding wouldn't be an issue.

I think I an going to try my pin router idea, I'm going to make a pin/guide that leaves about 1/32" left on the profile to cut then put the finish size pin/guide in and cut the last 1/32" hopefully there won't be any burning.

Fingers crossed.
jd99 is offline  
Old 11-25-2010, 03:06 PM   #15 (permalink)
Registered User
 
Join Date: Jun 2009
Country: United States
First Name: Danny
Posts: 523
jd99 is on a distinguished road

Default Update
Report Post Report This Post!

Well I got them all done, and finished with a coat of walnut oil. I'll give the a coat of wax tomorrow.
Attached Thumbnails
Sanding question-finished-trays.jpg  
jd99 is offline  
Old 11-26-2010, 04:14 AM   #16 (permalink)
Community Founder
 
Mark's Avatar
 
Join Date: Aug 2004
Country: Canada
First Name: Mark
Posts: 6,779
Mark has a spectacular aura about

Default
Report Post Report This Post!

Hey Danny, those turned out very nice!
Mark is offline  
Old 11-30-2010, 10:25 AM   #17 (permalink)
Vendor Account
 
Join Date: Dec 2008
Country: United States
First Name: Dan
Posts: 109
Eagle America is on a distinguished road

Default
Report Post Report This Post!

Danny - well done! We really liked seeing the photo of your finished bowls & trays. I think we are going to blog about your work. I can already see the smiles on the people's faces once they open up those gifts. Take care - Tim from Eagle America
__________________
Eagle America - "The World's Router Bit Source"
- Over 2,000 Eagle America and PriceCutter brand Router Bits
- Over 5,600 total woodworkiing items
Visit Us Online: http://www.EagleAmerica.com
Order 24 Hours A Day: 1-800-872-2511
Eagle America is offline  
Sponsored Advertisements. Register to disable this advertisement.
Old 11-30-2010, 10:58 AM   #18 (permalink)
Registered User
 
Join Date: Jun 2009
Country: United States
First Name: Danny
Posts: 523
jd99 is on a distinguished road

Default
Report Post Report This Post!

Quote:
Originally Posted by Eagle America View Post
Danny - well done! We really liked seeing the photo of your finished bowls & trays. I think we are going to blog about your work. I can already see the smiles on the people's faces once they open up those gifts. Take care - Tim from Eagle America
I'm currently working on the next set of trays, I have a maple and walnut tree ready to route, and have a cherry gingerbread man ready to hog out with the drill, and am glueing together several deferent widths of maple and cherry for the candycane. Plus I am going down today to get some Beech to make a couple of angels.

More pics to come.

I think we'll have 14 - 16 of them made by the time I'm done. Should be good experiance for next year it won't take me so long.
jd99 is offline  
Old 12-06-2010, 04:20 PM   #19 (permalink)
Registered User
 
Join Date: Dec 2010
Country: New Zealand
First Name: Tayler
Posts: 6
tailsnz is on a distinguished road

Default
Report Post Report This Post!

tight areas are always difficult. in nz my preferred wood is rimu (ree moo) which is a hardwood and burns easily. as said above the best way is to only make shallow cuts that can be cut away quickly. speed is the answer here before the wood overheats.
tailsnz is offline  
New Reply

Bookmarks

Go Back   Router Forums > Routers > General Routing
IconIt appears you arenít a registered member of the Router Forums community. Why not spend less than a minute and register for the oldest and largest router and woodworking community on the web! Join in over 29,500 discussions with over 65,000 woodworkers. If youíre an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account!



LinkBacks (?)
LinkBack to this Thread: http://www.routerforums.com/general-routing/24715-sanding-question.html
Posted By For Type Date
Beautiful Bowls & Trays Made By Someone Like You ę The Cutting Edge This thread Refback 04-24-2012 02:00 PM
The Cutting Edge This thread Refback 01-15-2011 01:41 AM
The Cutting Edge This thread Refback 12-08-2010 08:32 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Sanding sealer ? dwayne423 Lobby 15 12-16-2009 03:33 AM
Sanding Tips pmspirito Tools and Woodworking 7 05-22-2009 08:49 AM
Sanding Sealer - What is it? Thrifty Tool Guy The Finishing Touch 11 02-21-2009 08:28 AM
[FAQ] How to Post a Question Mark Forum Help & FAQ 0 01-11-2009 09:26 PM
DC Question angus Lobby 3 03-31-2008 07:29 PM