| |
| | Register Now!It appears that you aren't a registered member, click below to instantly register and become a member of the RouterForums.com Community! ** Registration removes majority of the website advertisements ** | |
| ||||||
| Introductions If you're new to our forums, tell everyone who you are in this area. Give us an idea of your background, hobbies and interests. |
New Reply |
| | Thread Tools | Display Modes |
01-25-2008, 07:33 PM
| #1 |
| Registered User |  Introduction and question I have recently set up a new woodshop and have a delta 43-355 shaper given to me by a friend. The spindle guard is broken and I am having trouble locating a new one, delta part (43-440). Any thoughts on where to get one or if it is ok to use the shaper without the spindle guard. Up until now I have used a router table but not a shaper. Thanks |
| Top - Reply with Quote |
 Sponsor Post
| |||
| Advertising
| Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Router Forums | ||
|
01-25-2008, 07:42 PM
| #2 |
| Forum Contributer Supreme Forum King  | Hi AlanO Is that the big thick ring  At one time I had a Grizzly shaper and I broke the one I had , so I picked some A325 Flat washers from a fastners outlet and did a bit of welding and made my own... The A325 washers are bit thicker than most washers and about the same size .. Just a note you should NOT use the shaper without one... Delta 43-455 Heavy Duty 1-1/4-Inch Solid Spindle 5-Horsepower Shaper with Micro Adjust Fence, 230-Volt 1 Phase Delta 43-812 Shaper Fence http://www.amazon.com/Delta-43-812-S...1353758&sr=1-4 ========== Last edited by bobj3; 01-26-2008 at 08:34 AM. |
|
| Top - Reply with Quote |
|
01-25-2008, 11:24 PM
| #3 |
| Official Greeter Supreme Forum King  Join Date: Sep 2004 Location: New Lebanon, Ohio "USA" First Name: Dave or "Doc" Posts: 4,715  | Welcome to the forums AlanO. Thanks for joining.
__________________ Dave the "Doctor" In woodworking there is no scrap, only firewood.  Please edit your profile with a name and location so we can better assist you and make for a friendlier forum. |
|
| Top - Reply with Quote |
|
01-26-2008, 03:56 AM
| #4 |
| Senior Moderator Supreme Forum King  | The first place to try is at the manufacturers parts department. The DeWalt service center handles all parts for Black & Decker, DeWalt, Porter Cable, Delta and DeVilbis. You can visit them by clicking here: http://www.deltaportercable.com/Serv...ndSupport.aspx
__________________ Mike Please edit your profile with a name and location so we can better assist you. |
|
| Top - Reply with Quote |
New Reply |
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Introduction/ Decline Cutting Techniques | gdrumz | Introductions | 8 | 03-15-2008 04:36 AM |
| Introduction and Question | djonesvb | Introductions | 10 | 12-28-2007 09:46 AM |
| Introduction | LonePalm | Introductions | 14 | 11-29-2007 08:09 AM |
| Caonoebuilder introduction, question | canoebuilder | Introductions | 9 | 07-26-2007 06:29 AM |
| Introduction and first question. | daddyrabbit | Introductions | 1 | 02-18-2006 02:37 AM |
Linear Mode
