Router Forums

Register Now!

It appears that you aren't a registered member, click below to instantly register and become a member of the RouterForums.com Community!

Register Now!

** Registration removes majority of the website advertisements **


Go Back   Router Forums > Routers > Jigs and Fixtures


New Reply
 
Thread Tools Display Modes
Old 12-06-2006, 10:48 PM   #1
robinette
Registered User
New Member
 
Join Date: Dec 2006
Location: Near Atlanta, GA
Posts: 3
robinette is on a distinguished road

Default Making an overhead router sled/jig

Not sure what to call it, but after making a couple decent good router tables, I thought I'd try something different. I got a Bosch Colt palm router, and I really like it for small work. And I've always like working with the router on top instead of under the table. Great visibility & freedom, etc. So... I thought I'd rig up something with rails. Not built yet, but the ideas are something like this:

- a 2'x4' surface to handle 48" x 18" or so
- a pair of small t-rails (a) running along the 4' lengths
- larger rails (b) that slide along the t-rails above, lockable with knobs
- a pair of small t-rails (c) mounted to the above sliders, that run perpendicular to the first set
- a pair of larger rails (d) that slide along this second set of t-rails, again with knobs that can lock their travel
- a router plate (e) mounted to these rails, tying the two together
- So far, then, the plate can move left/right and fwd/back unless locked down, and the workpiece rests on the 2'x4' surface
- straight edges to be mounted lengthwise (since exposed surfaces (b) move)

Note: small rails above fit perfectly inside the larger rails with no slack.
Several problems exist with this design, including:

- there is no mitering, only 0 or 90 degree routing (I have bigger problems!)
(ps: with all knobs loose, this rig could move diagonally in theory)
- there is no way to raise/lower the work piece, nor the router plate
- since the rails are all aluminum, stability/precision may be a problem

I can beef it up by sinking some of the rails into wood. And/or gluing or welding rails (b and c) together, but I'm not sure locking at 90 degrees is a great idea. But the biggest issue is that there's no way to adjust the height of the router or work piece.

Short of a set of chain-driven cranks, I haven't thought of a way to address the height/depth issue. Any thoughts welcome. Anyone tried anything like this? Thanks.......

Randy
robinette is offline   Top - Reply with Quote
Alt Sponsor Post
Advertising


Alt Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Router Forums
   
Old 12-08-2006, 02:10 AM   #2
Mike
Senior Moderator
Supreme Forum King
 
Mike's Avatar
 
Join Date: Nov 2004
Location: Detroit, Michigan USA
Posts: 3,159
Mike has disabled reputation

Send a message via AIM to Mike Send a message via Yahoo to Mike Send a message via Skype™ to Mike

Randy, there are plans for building overhead or overarm routers. Some of these are also called pin routers. You will also find plans or at least postings about home built CNC routers. The question is: How much production work are you planning on doing to require a router of this type? If this is just a project to see if you can build it, you can. Professional sign shops use CNC routers. ($$$) The same mechanisims are used for CNC Plasma torch cutting tables. The router or plasma head are attached to an acme screw that is powered up or down by servo motors. Why not leave the X,Y & Z stuff to those who really need it and keep it simple and fun?

PS: If you want to build something really useful for your palm router see Shopnotes Vol. 15, Issue 90 (on sale at news stands now) for the article on the 3-in-1 portable multi-tool. This allows you to use your palm router as a router table, mortiser or edge jointer.
__________________
Mike

Last edited by Mike; 12-08-2006 at 02:19 AM.
Mike is offline   Top - Reply with Quote
Old 12-08-2006, 11:46 AM   #3
robinette
Registered User
New Member
 
Join Date: Dec 2006
Location: Near Atlanta, GA
Posts: 3
robinette is on a distinguished road


Mike, thanks. More I think about it, this is a lot of overkill. It's not for production work at all. Just getting back into it, and my old router tables were fun but not so easy to change bits etc. Although short on power, I really like the palm because it's so tiny, and thought I could rig up something easy with sliders in both directions. But the more I got into it, it started to look less useful, more complicated, and kind of a dumb idea. Before I gave up on it, I thought I'd get some feedback here.

So, thanks for the tip, I'll checkout the Shopnotes article.
Randy
robinette is offline   Top - Reply with Quote
New Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Mixing Bosch 1617 Router fixed base with Craftsman professional router sf_basilix Starting Off 5 01-21-2008 08:54 AM
Motorized Router Lift - Eagle Lake Style johnwnixon Table-mounted Routing 10 09-13-2007 06:59 AM
RouterForums.com and Oak-Park.com - September 2006 Contest - VOTING STAGE!! Mark Contests Archive 13 11-05-2006 02:23 AM
RouterForums.com and Oak-Park.com - September 2006 Contest!! Mark Contests Archive 72 10-01-2006 12:02 PM
New Router my way reible General Routing 14 06-10-2006 10:19 PM


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd. Search Engine Optimization by vBSEO 3.2.0
Copyright 2007 RouterForums.com

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109