Router Forums - View Profile: 4DThinker

 

4DThinker 4DThinker is offline

Registered User

  About Me

  • Woodworker Information
    A few details about myself.
    First Name
    4D
    Country
    United States

  Statistics

Total Posts
General Information
  • Last Activity: Yesterday 08:33 PM
  • Join Date: 02-16-2014
  • Referrals: 0

  Mentions

No results to display...

  Quotes

01-09-2017
12:10 PM - MEBCWD quoted 4DThinker in post More Buffalo Nickels
You can set how fine of resolu...
01-08-2017
09:38 PM - RainMan 2.0 quoted 4DThinker in post More Buffalo Nickels
If I only had one to scan. M...
02:29 PM - MEBCWD quoted 4DThinker in post More Buffalo Nickels
If I only had one to scan. M...
12:36 PM - 4DThinker quoted honesttjohn in post More Buffalo Nickels
Send me the file 4D. It shows...
01-02-2017
11:42 AM - 4DThinker quoted MEBCWD in post Thin Bed Vise
Spare Time ??I always thoug...
01-01-2017
10:16 AM - 4DThinker quoted honesttjohn in post Thin Bed Vise
Where there's a will -- there's ...
11-13-2016
05:15 PM - sawnsand quoted 4DThinker in post Z axis repeetability ?
Any chance you can post the te...
11-05-2016
01:51 PM - difalkner quoted 4DThinker in post 2nd Build (first) - CNC Router
"no-no" sounds like a great na...
01:32 AM - 4DThinker quoted difalkner in post 2nd Build (first) - CNC Router
Climate controlled shop - open...
11-04-2016
12:24 PM - difalkner quoted 4DThinker in post 2nd Build (first) - CNC Router
No beating the dust a CNC make...
10-24-2016
07:21 PM - Jbird22 quoted 4DThinker in post Probotix - Feed & Plunge Rate help needed
During 3D cuts the feed speed ...
10-11-2016
02:22 AM - 4DThinker quoted whimsofchaz in post Probotix vs. Shopbot
Why not use a vacuum table?Many ...
01:59 AM - whimsofchaz quoted 4DThinker in post Probotix vs. Shopbot
No obvious potential for verti...
09-19-2016
03:45 PM - 4DThinker quoted OPG3 in post Small angle clamping jig.
4D, I was taught that the...
07-19-2016
10:58 AM - difalkner quoted 4DThinker in post 2nd Build (first) - CNC Router
I don't make guitars or anythi...
10:15 AM - difalkner quoted 4DThinker in post 2nd Build (first) - CNC Router
Dust/chips from hardwoods are ...
07-09-2016
02:28 PM - difalkner quoted 4DThinker in post 2nd Build (first) - CNC Router
When you build the table for i...
06-24-2016
11:16 AM - Stick486 quoted 4DThinker in post Building furniture on a CNC from paper plans?
This CNC stuff is just too awe...
05-29-2016
04:50 PM - RainMan 2.0 quoted 4DThinker in post Any experience with Probotix CNC units out there?
Simple desk design. Tenon arr...
05-18-2016
04:55 PM - honesttjohn quoted 4DThinker in post The best seat in the house
Ok Jay. You are officially no...
 
For the best viewing experience please update your browser to Google Chrome