| |
| | Register Now!It appears that you aren't a registered member, click below to instantly register and become a member of the RouterForums.com Community! ** Registration removes majority of the website advertisements ** | |
04-21-2008, 02:12 PM
| #11 |
| Registered User Sr. Member |  BobJ, That "Bottoming Bit" looks interesting. Who makes it, does it come in different widths and where can it be purchased? Joe Z.
__________________ JoeZ  If you never made a mistake, you never tried anything
|
| Top - Reply with Quote |
 Sponsor Post
| |
| Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Router Forums | |
|
04-21-2008, 02:29 PM
| #12 | |
| Forum Contributer Supreme Forum King  | Hi Joe I get some of them off eBay, he has diff. sizes from time to time but they must be the square blade type not the normal round bottom bit..see note below. http://www.routerforums.com/70844-post7.html http://cgi.ebay.com/ws/eBayISAPI.dll...TODAY.m238.lVI http://stores.ebay.com/Super-Carbide-Tools But other types of bits can be use in the same way, like the one below http://cgi.ebay.com/1-pc-1-2-SH-New-...742.m153.l1262 http://cgi.ebay.com/1-pc-1-2-SH-New-...742.m153.l1262 http://cgi.ebay.com/2pc-1-2-Shank-We...742.m153.l1262 http://cgi.ebay.com/1-pc-1-4-SH-1-4-...742.m153.l1262 http://cgi.ebay.com/BRAND-NEW-1-Dia-...QQcmdZViewItem ========= Quote:
__________________ Workshop Projects Router Tables plans FREE, plus more http://www.absolutelyfreeplans.com/W...p_projects.htm RW Router Tip Archive www.routerworkshop.com/router_tip_glossary.html Floating Mortise & Tenon: A strong and Silent Joint Last edited by bobj3; 04-22-2008 at 10:54 AM. | |
|
| Top - Reply with Quote |
|
04-25-2008, 10:57 AM
| #13 | |
| Forum Contributer Supreme Forum King | You'er Welcome smokeyone One more note the jig works great for making tentons ,sliding dovetails,blind dovetails,dado,etc. one pass on both sides then just flip the stock on it's edge and with a pass or two the tenton is done and it's a real clean job...without any saw marks...plus you can off set the tenton easy by just moving the bit up or down and with the brass setup bars, it's always right on the mark...the stock can be just about any size you want to use...from 1/4" thick to 4" thick stock..when you use a strait bit (1/2"). ================ Quote:
__________________ Workshop Projects Router Tables plans FREE, plus more http://www.absolutelyfreeplans.com/W...p_projects.htm RW Router Tip Archive www.routerworkshop.com/router_tip_glossary.html Floating Mortise & Tenon: A strong and Silent Joint Last edited by bobj3; 05-16-2008 at 10:50 AM. | |
|
| Top - Reply with Quote |
New Reply |
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Incra Ultra How-To (Box Joints + Other Stuff) | Nickbee | Show N' Tell | 5 | 01-21-2008 08:14 AM |
| Best bit for tight fitting box joints? | Nickbee | Router Bits - Types and Usage | 9 | 12-31-2007 12:13 AM |
| Locking mitre joints for picture frames | grandsire02 | Table-mounted Routing | 3 | 08-10-2007 01:56 AM |
| Drawer joints - Box vs. Dovetail vs. ??? | ChevyNomad | General Routing | 2 | 01-14-2005 10:20 AM |
Linear Mode
