Dave Bishop

I learned that my image size (3072 x 2304) is too large to upload, so will need to take more pictures another day and upload then. Keep watching!

Hamlin

Hi Dave,

If you have Paint.Net or PaintShopPro or other type program, you can resize them to fit. I learned this the hard way until Bj taught me how to change the sizing of the pics.

__________________
Ken

"A VETERAN"
"Wether active duty, retired, national guard or reserve - is someone who, at one point in their life, wrote a blank check made payable to "The United States of America", for an amount of "up to and including my life". That is HONOR, and there are way too many people in this country who no longer understand it." -Author Unknown

bobj3

Hi Dave

You can download FREE software but do this , upload your pictures to
http://tinypic.com/
They will resize them for you and give you a url code,,,that you can use but you will still run into the 10 post min.thing..but you are on 7 so it will only take 3 more to get over the 10. just say hi 3 time in this thread and it's done with...

Do this goto http://www.irfanview.com/ and get the free software that will let you rezise the snapshots so you can upload them to the forum..

JUST a note ****** the 10 post thing is only for the URL items,,it should let you post pictures right off the bat but they must not be to big...
If I recall it's 999 x 999 ...


=============

__________________
Workshop Projects
Router Tables plans FREE, plus more
http://www.absolutelyfreeplans.com/...op_projects.htm

RW Router Tip Archive
www.routerworkshop.com/router_tip_glossary.html

Dave Bishop

Finally, here are photos of the "cyma recta" profile and the steps I used to make it:

Photo #1: This is taken from FWW #166, p. 74 (Dec. 2003). This is the built-up molding I want to make. It consists of (from the top) quarter round, fillet, cyma recta, fillet, elongated cove, astragal, and cove. The cyma recta is what I wanted to duplicate using roundover and cove bits.

Photo #2: A front view of the 30° fence and retainer mounted to my router table.

Photo #3: A side view showing how the stock will ride on the retainer and be held against the fence.

Photo #4: The first cut, made with a 3/8" roundover bit with the bearing removed.

Photo #5: After the second cut, made with a 3/8" cove bit (bearing removed) with the stock flat on the table. A 3/4" roundnose bit would have worked here, too.

Photo #6: Showing how the notch due to the overcut of the roundover bit will be hidden when the molding is built up.

Attached Thumbnails

         

 

Dave Bishop

Thanks to all with the suggestions on how to post pictures. The size limit is 2000 x 2000 - I learned this from an error message. So I went back, set my camera for 1600 x 1200, and took more photos, the ones I have now uploaded.

Dave

bobj3

You Welcome Dave

When you resize them they will upload quicker and popup quicker, I used one of your snapshots a resize it , for a show and tell thing..

Yours is 453.85 kb and the one I reworked is 10.9 kb..
You will see it jump up quick when you click on it...
==========

Attached Thumbnails

 

__________________
Workshop Projects
Router Tables plans FREE, plus more
http://www.absolutelyfreeplans.com/...op_projects.htm

RW Router Tip Archive
www.routerworkshop.com/router_tip_glossary.html

Dave Bishop

That's quite a diiference in file size and performance, with no noticeable change in appearance. I need to look at those sites you mentioned. Thanks.

Charles M

Wish you had posted a picture of what you wanted in the beginning. The moulding you made is what I always thought was the Cyma Reversa. This may have worked for you:


Click to Enlarge

__________________
Charles M
Freud America, Inc.