Katie

I am looking for some free plans to build a bookcase similar to this one. This is not a project I built, just an example of what I want to do. If anyone knows where I can find some free plans similar to this I would greatly appreciate it. TIA

Katie

Attached Thumbnails

 

Advertising

BobandRick

Katie: maybe we talk about the size you want to make and the equipment you have then together we make your own plan.

__________________
Rick and Bob
The Router Guys

Click here to send a greeting card to friend or relative.

Katie

Oh that would be great. I think it looks pretty simple but I am new to this so any help would be awesome. I think I would like it to be a four teir. The books are supposed to set forward facing out in the slots. The ones I have seen are only about 3 inches setback for each level, and the backs of the levels are just slightly angled back so the books will lean back instead of forward when resting in the slots. I would prefer it did not have the extended legs. About 25 inches wide and no more than 15 inches deep. I want it to set on top of my daughters dresser. I have very few tools of my own. Just a circular saw, a mouse sander and a drill. If I need to I can borrow a scroll saw and router from my dad. I would like to keep it as simple as possible because I am just learning. I was thinking of using MDF and painting it. Thank you for your help. I am thinking two triangular pieces for the sides. This is what I have come up with so far. I know this is a very crude drawing but bear with me. I would love to hear your ideas on this. (see pic below) The red lines are the end piecies and the blue lines are where I would line up the pockets. It looks like I would need
one 4 x 23 inches
four 3 x 23 inches
and four 7 x 23 inches. Does that look like it will work to you?
Thank you so much for taking a look at this for me.

Katie

Attached Thumbnails

 

BobandRick

The drawing looks good. One comment: It looks a bit crowded with 4 tiers maybe 3 would be better for the 14" wide or how effective is 3" deep? Remember we have the tiered shelves so we can see the books right? With 3" wide there will be a lot of books behind other books. Maybe 4 tiers but the shelf width is only 2" wide.

You say you have a router. Plunge or Fixed Based? Is the router table mounted or portable? Any router bits? Any guides?

__________________
Rick and Bob
The Router Guys

Click here to send a greeting card to friend or relative.

Katie

I think you are right about making them a 2 inch depth instead of a 3 inch. Then there will be more books showing. I am also wondering if the 4 inches will be too deep for the pockets. We are going to the preschool tomorrow, so I will take a tape measure and check the demensions on the one there.

The router belongs to my Dad who is not a woodworker. I called him today and asked if I could borrow it. He is going to drop it by on wednesday. He said he has never used it and does not know what kind it is. I think it is a plunge. He said it has a little portable table with it. He said he is not sure if there are any bits or guides with it. If I need to I can go buy a bit. It looks like I will have to wait till wednesday to see exactly what it is. I will post the info as soon as I can. Thanks again.

Katie

BobandRick

I will wait until your next post

__________________
Rick and Bob
The Router Guys

Click here to send a greeting card to friend or relative.

Katie

Ok I got the router and the scroll saw today. the router is a craftsman model 315.17492 and the scroll is a shop fox w1713 variable speed. I have been looking online and could not find any info on this router. I have never used one before so I am not sure what type it is but I think it is a plunge. My dad said it had a little portable table with it when he got it, but he could not find it. There are no bits or guides either, so I will have to go buy a bit. I am just not sure what kind I will need. I measured the book case at the preschool and it was about two inches from front to back of the slots, and about three inches from top to bottom of the slot/pocket.

BobandRick

We don't really have many router accessories so lets do this project without the router this time. I would suggest that we use the butt joint for the shelves and screws to tie this project together.

Let's start by laying out one side of the shelf on graph paper. We need two sides but we are going to use just the one pattern to get the information on the both the left and right sides. We need the positioning of the shelves and screws on the graph paper. To do this can you get graph paper to make a full scale pattern. Then transfer this pattern to one side of your MDF.

To get the other side's layout we are going to use the back side of your paper pattern. One side of the pattern will be the right hand side and the other side of the pattern will be the left hand side.

If you can't see the lines and screws on the back side of the pattern... tape the graph paper pattern face down on to a window and let the sun light be your light table to transfer the lines and screw positions to the back of the pattern.

Lets do this then we will talk about the sizes of the shelves and supports on the material list next.

__________________
Rick and Bob
The Router Guys

Click here to send a greeting card to friend or relative.

Katie

Ok I have it scaled down so tomorrow I will take some time and get the full size pattern made up. Thanks.

reible

I know I'm coming in a little late on this but when I saw the first sketch I knew this looked like something I have in a book called Make-it-yourself Equipment Encyclopedia compiled by Eleanor l. Doan. I think I got this around 1980 at a Christian book store it was published by Gospel Light and cost $2.25. There are 200 projects in the book and I only built a few, and not the Two-Way Library (this is what they called this piece).

This one is a good deal larger then what you want and rolls around on wheels and includes three shelves on the oposite side of the display.

If you are interested in seeing what this one looks like private message me and give me an email address to send it to.

I have no idea if this book is still around but I made several projects for my kids (the youngest is now 26) and I still have at least a few of the projects hanging about the house.... All the project are simple to build and require few tools.

Ed