Router Forums

Register Now!

It appears that you aren't a registered member, click below to instantly register and become a member of the RouterForums.com Community!

Register Now!

** Registration removes majority of the website advertisements **


Go Back   Router Forums > Other > Show N' Tell

Rate This Thread - Hoizontal Router Table.

New Reply
 
Thread Tools Display Modes
Old 07-31-2006, 09:21 PM   #1
RustyW
Registered User
Forum Geek
 
RustyW's Avatar
 
Join Date: Dec 2005
Location: Oroville CA, USA
Posts: 295
RustyW is on a distinguished road

Default Hoizontal Router Table

This is a table I put together over the weekend. Some parts are a little primative and still needs some fine tuning. But it works and was made out of stuff I allready had lying around the garage. The 3/8" threaded rod I used for "fine" adjustments might get changed as a full turn only moves it 1/16". On top of the table is a push block I also made this weekend. I got the pattern for the handle out of magazine and also made one for my old homemade coping sled. I had some left over non-slip shelf liner (like a router mat only thinner) that I glued to the bottom of the push block. Works really good.

First time adding pics, hope it works.

Rusty
Attached Thumbnails
hoizontal-router-table-volume4-215.jpg  hoizontal-router-table-volume4-216.jpg  hoizontal-router-table-volume4-217.jpg  hoizontal-router-table-volume4-218.jpg  
RustyW is offline   Top - Reply with Quote
Alt Sponsor Post
Advertising


Alt Sponsored Links



__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Router Forums
   
Old 07-31-2006, 11:25 PM   #2
Dr.Zook
Official Greeter
Supreme Forum King
 
Dr.Zook's Avatar
 
Join Date: Sep 2004
Location: New Lebanon, Ohio "USA"
Posts: 4,180
Dr.Zook is on a distinguished road

Send a message via Skype™ to Dr.Zook
Default

Hey Rusty. Your first time adding pics looks great. Real nice router system you have there. Making do with what you have is more rewarding at times. Nice work and I really like the coping sled.
__________________
Dave
the "Doctor"

In woodworking there is no scrap, only firewood.
Dr.Zook is offline   Top - Reply with Quote
Old 08-01-2006, 09:43 AM   #3
bobj3
Forum Contributer
Supreme Forum King
 
bobj3's Avatar
 
Join Date: Jan 2006
Location: Littleton,Colorado U.S.A.
Posts: 7,137
bobj3 is a jewel in the roughbobj3 is a jewel in the roughbobj3 is a jewel in the rough

Default

Nice job Rusty

Just a note about the "full turn only moves it 1/16"" that's just about what you want when you are making panels and slots....once you know for sure what ea. turn will do you now have quick gage to go by and 1/16" is a big deal when it comes to panels or slots.

Great ideal on the non-slip shelf liner, I for one will tell (ask ) my boss to pick some when she out Walmart shopping ... ,I just now put it on my want list for the boss along with some 3M clear shipping tape.

That's what neat about this forum you can pickup tips all the time.

Nice job on the sled , here's a tip, use some of the same black plastic stock when you go to make the bead cuts, just stick a 6" wide x 18"long, stick it down to the table top,(with Doub,Side Carp.Tape(3M) in this way you don't need to reset the router height the norm, just pop in the bead cutter and cut the stiles, rails, for the doors,if you are using a match set of cutters (the norm) they should come out right on the button.

Just a NOTE ****
Looks like you just saved 189.00 bucks or so see link below...now that's the neat part of wood working....

http://www.mlcswoodworking.com/shops...horiztabl.html
===========

If you want to make your own here's a link that will help with that.
http://stores.ebay.com/8020-Inc-Garage-Sale

=============
Have a good one
Bj

Last edited by bobj3; 04-17-2008 at 10:09 AM.
bobj3 is offline   Top - Reply with Quote
Old 08-02-2006, 11:57 AM   #4
Glenmore
Forum Moderator
Supreme Forum King
 
Glenmore's Avatar
 
Join Date: Sep 2004
Location: Mountain Top Pennsylvania
Posts: 1,448
Glenmore will become famous soon enough

Send a message via Skype™ to Glenmore
Default

Rusty that is a great table you made. Seen one of them from MCLS you probably didn't pay as much as they are asking. Like the set up for your router adjustment.
__________________
Glenmore

Days without wood working are days not worth getting up for.
Glenmore is offline   Top - Reply with Quote
Old 08-09-2006, 05:59 PM   #5
Hamlin
Registered User
Supreme Forum King
 
Join Date: Dec 2005
Location: Baldwin City, KS
Posts: 1,374
Hamlin is an unknown quantity at this point

Send a message via MSN to Hamlin
Default

That is excellent work, especially for a being a "weekend" project. Nicely done!!
I think you should keep the 3/8" threaded rod. You already know what each turn gives you, perfect gauge for your router work.
__________________
Ken

(On temporary leave of abscense)

"A VETERAN"
"Wether active duty, retired, national guard or reserve - is someone who, at one point in their life, wrote a blank check made payable to "The United States of America", for an amount of "up to and including my life". That is HONOR, and there are way too many people in this country who no longer understand it." -Author Unknown
Hamlin is offline   Top - Reply with Quote
Old 08-10-2006, 05:49 PM   #6
Lee Brubaker
Registered User
Forum Fanatic
 
Join Date: Jan 2006
Posts: 137
Lee Brubaker is on a distinguished road

Default

Rusty: As Bj says, 1/16th per full turn is just right. Think more than panels. I use mine to make sliding dovetails, edge jointing, etc, etc. Mine uses two threaded rods instead of one(at each end)hence, if you leave one end locked & turn only one threaded rod, the adjustment is half that of a single rod full turn ie: 1/32nd. For sliding dovetails this can be important. Namely 1/2 turn = 1/64th, a quarter turn = 1/128th. Longest sliding dovetail I have made so far has been 42" long. An excellent breadboard attachment. I didn't note a dust collection port ? I presume that there is one ?

Lee
Lee Brubaker is offline   Top - Reply with Quote
Old 08-10-2006, 08:51 PM   #7
bobj3
Forum Contributer
Supreme Forum King
 
bobj3's Avatar
 
Join Date: Jan 2006
Location: Littleton,Colorado U.S.A.
Posts: 7,137
bobj3 is a jewel in the roughbobj3 is a jewel in the roughbobj3 is a jewel in the rough

Default

Hi Rusty
I just want to say thanks again for the tip on the
"non-slip shelf liner"
That suff is great ,I had the BOSS pick up 3 rolls that are 12" wide x 5ft long and it was only 3.oo bucks a roll, white and blue, I put it on kinds of items in the shop,push blocks,on the bottom of router boxes,inside the tool box so the tools don't move around,you name it I put it on it... great stuff, I used 3M spray glue to hold it on.
I also put it on the bottom of the wifes inside shoes ,LOL now she can't slide on the kitchen floor any more (big kid) hahahahahahaha or slip off the chair (a little foot tall kids chair) but she calls it her ladder. I made a step stool for her but she likes her little blue chair...

anyway thanks again Rusty
Bj

Last edited by bobj3; 08-11-2006 at 10:40 AM.
bobj3 is offline   Top - Reply with Quote
New Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Insert Plate size and 11.5" handle spread; how to prevent problems Ladd Table-mounted Routing 34 12-14-2007 01:08 PM
Motorized Router Lift - Eagle Lake Style johnwnixon Table-mounted Routing 10 09-13-2007 06:59 AM
First and only (I hope!) Router table CanuckBeaver Table-mounted Routing 11 07-25-2007 02:45 PM
Problem mounting Dewalt Router to Caftsman Table Saw apollo2000 General Routing 8 05-22-2007 06:42 PM


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd. Search Engine Optimization by vBSEO 3.2.0
Copyright 2007 RouterForums.com

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107