router table feed systems - Router Forums
Help
Require Assistance? Read the Beginners Guide to RouterForums.com
RouterForums.com - Router and Woodworking Discussion Community

Go Back   Router Forums > Routers > Table-mounted Routing
IconIt appears you arenít a registered member of the Router Forums community. Why not spend less than a minute and register for the oldest and largest router and woodworking community on the web! Join in over 29,500 discussions with over 65,000 woodworkers. If youíre an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account!

router table feed systems

This is a discussion on router table feed systems within the Table-mounted Routing forums, part of the Routers category; I plan on milling 8 ft. long pieces of mdf for casings, baseboards, and other ...


  • Replies: 4, Views: 1411

New Reply
 
LinkBack Thread Tools Display Modes
Old 10-23-2010, 10:40 AM   #1 (permalink)
Registered User
 
Join Date: Oct 2010
Country: Canada
First Name: dave
Posts: 3
kiteboarder is on a distinguished road

Default router table feed systems
Report Post Report This Post!

I plan on milling 8 ft. long pieces of mdf for casings, baseboards, and other pieces related to a wainscotting project and would like a make a manual or power feed systems that would secure the pieces properly. Does anybody have plans or ideas for this? Thanks.

kiteboarder is offline  
Sponsored Advertisement - Register now to remove this advertisement.
** Please be sure to read our Disclaimer at the bottom of the page. **

Advertisement

These advertisements are only displayed to guests, register now for your FREE account on the worlds largest router and woodworking community!
Old 10-23-2010, 10:59 AM   #2 (permalink)
Forum Contributor
 
Join Date: Jan 2006
Country: United States
First Name: Bj
Posts: 23,793
bobj3 has a brilliant futurebobj3 has a brilliant futurebobj3 has a brilliant futurebobj3 has a brilliant future

Default
Report Post Report This Post!

Hi Dave

You can get one from Grizzy, it's best to just buy one ,this type of tool must be right from the get go, I was going to make my own by using the power belt sander and the cost was so much higher than just buying one out right..it can be used on the router table,table saw,RAS, and many other tools in the shop..

G4173 Baby Power Feeder

==========

Quote:
Originally Posted by kiteboarder View Post
I plan on milling 8 ft. long pieces of mdf for casings, baseboards, and other pieces related to a wainscotting project and would like a make a manual or power feed systems that would secure the pieces properly. Does anybody have plans or ideas for this? Thanks.
__________________
"It's fine to disagree with other members as long as you respect their opinions"

Marc Sommerfeld Tools ,Videos
http://www.youtube.com/channel/UCT-n...RWaEpMA/videos

Find all threads started by bobj3
http://www.routerforums.com/search.php?searchid=944097


bobj3 is offline  
Old 10-24-2010, 08:39 AM   #3 (permalink)
Registered User
 
Join Date: Oct 2010
Country: Canada
First Name: dave
Posts: 3
kiteboarder is on a distinguished road

Default
Report Post Report This Post!

thanks bob. I downloaded the manual and I'm confused about table saw use. The manual shows the power feeder mounted directly over the blade. How can this happen without damage to the unit? If it can work like this, Would it be a good overarm dust collector for the table saw, as I plan on building one of those as well. Thanks for all your help.
kiteboarder is offline  
Old 10-24-2010, 08:40 AM   #4 (permalink)
Registered User
 
Join Date: Oct 2010
Country: Canada
First Name: dave
Posts: 3
kiteboarder is on a distinguished road

Default power feeder
Report Post Report This Post!

[quote=kiteboarder;207253]thanks bob. I downloaded the manual and I'm confused about table saw use. The manual shows the power feeder mounted directly over the blade. How can this happen without damage to the unit? If it can work like this, Would it be a good overarm dust collector for the table saw, as I plan on building one of those as well. Thanks for all your help.
kiteboarder is offline  
Old 10-24-2010, 09:42 AM   #5 (permalink)
Forum Contributor
 
Join Date: Jan 2006
Country: United States
First Name: Bj
Posts: 23,793
bobj3 has a brilliant futurebobj3 has a brilliant futurebobj3 has a brilliant futurebobj3 has a brilliant future

Default
Report Post Report This Post!

Hi Dave

Your Welcome
I'm sure they don't want you to use it that way ,to one side of the blade, I'm sure the person that draw up the info has not use a table saw but it would be great for dado cuts ,that I hate to do on the table saw..they do like to lift the stock up and shoot it into the wall on the other side of the shop...



===========

[quote=kiteboarder;207254]
Quote:
Originally Posted by kiteboarder View Post
thanks bob. I downloaded the manual and I'm confused about table saw use. The manual shows the power feeder mounted directly over the blade. How can this happen without damage to the unit? If it can work like this, Would it be a good overarm dust collector for the table saw, as I plan on building one of those as well. Thanks for all your help.
__________________
"It's fine to disagree with other members as long as you respect their opinions"

Marc Sommerfeld Tools ,Videos
http://www.youtube.com/channel/UCT-n...RWaEpMA/videos

Find all threads started by bobj3
http://www.routerforums.com/search.php?searchid=944097



Last edited by bobj3; 10-24-2010 at 03:08 PM.
bobj3 is offline  
New Reply

Go Back   Router Forums > Routers > Table-mounted Routing
IconIt appears you arenít a registered member of the Router Forums community. Why not spend less than a minute and register for the oldest and largest router and woodworking community on the web! Join in over 29,500 discussions with over 65,000 woodworkers. If youíre an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account!



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Mixing Bosch 1617 Router fixed base with Craftsman professional router sf_basilix Starting Off 17 10-11-2012 06:20 PM
Problem mounting Dewalt Router to Caftsman Table Saw apollo2000 General Routing 14 08-13-2012 02:07 PM
First Benchtop Router Table, get a plate or go bare? silentblackhat Table-mounted Routing 38 05-30-2012 03:30 AM
New Router my way reible General Routing 20 11-30-2011 12:18 PM
Already Problems neuschu Introductions 11 12-15-2009 08:01 AM