Help
Require Assistance? Read the Beginners Guide to RouterForums.com
RouterForums.com - Router and Woodworking Discussion Community

Go Back   Router Forums > Routers > Table-mounted Routing
IconIt appears you arenít a registered member of the Router Forums community. Why not spend less than a minute and register for the oldest and largest router and woodworking community on the web! Join in over 29,500 discussions with over 65,000 woodworkers. If youíre an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account!

angled mortise on a router table.

This is a discussion on angled mortise on a router table. within the Table-mounted Routing forums, part of the Routers category; I am building a baby's high chair and I need to cut 7 degree angled ...


  • Replies: 1, Views: 876

New Reply
 
LinkBack Thread Tools Display Modes
Old 02-26-2012, 05:07 PM   #1 (permalink)
Registered User
 
Join Date: Jul 2011
Country: New Zealand
First Name: Terry
Posts: 1
sooter is on a distinguished road

Default angled mortise on a router table.
Report Post Report This Post!

I am building a baby's high chair and I need to cut 7 degree angled mortises in the legs to take the leg braces. Leg braces would also have a 7 degree angled mortise. I hope I have the terminology right.
Is there a simple way / jig to achieve this. I tried some trials on a table saw but the cuts are too rough.
I have a Ryobi router and table and thought this may be the way to go.
I have straight bits only tho.

Stock is 18mm x 55mm wide. Mortice depth I thought would be half depth (9mm).
Attached is dwg file of my plan.
Any ideas would be greatly appreciated.

Attached Files
File Type: zip high chair side view.zip (13.8 KB, 27 views)
sooter is offline  
Sponsored Advertisement - Register now to remove this advertisement.
** Please be sure to read our Disclaimer at the bottom of the page. **
These advertisements are only displayed to guests, register now for your FREE account on the worlds largest router and woodworking community!
Old 02-29-2012, 03:32 PM   #2 (permalink)
Forum Liaison
 
Mike's Avatar
 
Join Date: Nov 2004
Country: United States
First Name: Mike
Posts: 10,583
Mike is a jewel in the rough

Send a message via Skype™ to Mike
Default
Report Post Report This Post!

Terry, Save your file as a PDF so we can open it. Google freePrimo pdf
__________________
Mike
"Living in the D" (this means Detroit!)
"It's fine to disagree with other members as long as you respect their opinions"
Mike is offline  
New Reply

Bookmarks

Go Back   Router Forums > Routers > Table-mounted Routing
IconIt appears you arenít a registered member of the Router Forums community. Why not spend less than a minute and register for the oldest and largest router and woodworking community on the web! Join in over 29,500 discussions with over 65,000 woodworkers. If youíre an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account!

Tags
router table advice


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Getting Started With A Woodworking Router. learnexperience Table-mounted Routing 7 04-20-2014 07:57 PM
Anyone converted a table saw to router table? OneStaple Table-mounted Routing 54 02-08-2014 04:17 PM
Problem mounting Dewalt Router to Caftsman Table Saw apollo2000 General Routing 14 08-13-2012 01:07 PM
New Router my way reible General Routing 20 11-30-2011 11:18 AM
what is the problem of making mortise with table router? volunteers Table-mounted Routing 4 04-09-2011 09:30 AM