| |
| | Register Now!It appears that you aren't a registered member, click below to instantly register and become a member of the RouterForums.com Community! ** Registration removes majority of the website advertisements ** | |
| ||||||
| Table-mounted Routing Discussions solely based on operations that are using the table-mounted router. Bob and Rick say "More than 90% of all operations using the router can be done with the table-mounted router. |
New Reply |
| | Thread Tools | Display Modes |
12-30-2006, 12:08 PM
| #1 |
| Registered User Dedicated Member |  Using brass setup bars How, exactly, are setup bars used to isolate the bearing? Bob does it too fast to see clearly. Bruce in the Peg
__________________ Bruce in the Peg |
| Top - Reply with Quote |
 Sponsor Post
| |||
| Advertising
| Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Router Forums | ||
|
12-30-2006, 01:24 PM
| #2 |
| Marine Engineer Forum King  | Bruce, The way he uses the setup bars (or any other straight edge) to isolate the bearing is pretty straightforward. All you are doing is making the bearing flush with the infeed and outfeed sides of the fence. If you're touching all 3 at the same time, you've isolated the bearing.
__________________ Doug 1 John 1:9 |
|
| Top - Reply with Quote |
|
12-30-2006, 02:44 PM
| #3 |
| Forum Contributer Supreme Forum King  | Hi Bruce Here's a HowTo link that may help  http://www.routerworkshop.com/Tipb4.html http://www.routerforums.com/email-ro...g-bearing.html Bj
__________________ PodCast videos RWS on YouTube http://www.routerforums.com/86898-post1.html Besure and click on the Up Arrow key ▲ on the Youtube video, you can select other youtube videos on router tables http://www.woodworkingonline.com/?s=dovetail Machine Cut ▼ http://www.woodworkingonline.com/200...cut-dovetails/ http://www.woodworkingonline.com/woo...podcast-store/ http://www.woodshopdemos.com/menu2.htm Bob J. |
|
| Top - Reply with Quote |
|
12-30-2006, 03:52 PM
| #4 |
| Registered User Dedicated Member | Bob, what on earth does it help to practice isolating the bearinf after the fence has been removed? See the very last paragraph on either of the links. BB
__________________ Bruce in the Peg |
|
| Top - Reply with Quote |
|
12-30-2006, 04:09 PM
| #5 |
| Forum Contributer Supreme Forum King | Hi Bruce I think he is sayiing to put the fence back and do it again and again just for practice,if you don't remove the fence you can't go back and do it over from sq. 1. Bj
__________________ PodCast videos RWS on YouTube http://www.routerforums.com/86898-post1.html Besure and click on the Up Arrow key ▲ on the Youtube video, you can select other youtube videos on router tables http://www.woodworkingonline.com/?s=dovetail Machine Cut ▼ http://www.woodworkingonline.com/200...cut-dovetails/ http://www.woodworkingonline.com/woo...podcast-store/ http://www.woodshopdemos.com/menu2.htm Bob J. |
|
| Top - Reply with Quote |
New Reply |
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Oak Park Mitre Gauge - Need Setup Help.. | Chris H | Jigs and Fixtures | 3 | 07-06-2008 11:39 PM |
| Permanent Dado Setup | arkwood | General Routing | 3 | 05-22-2007 11:06 PM |
| Brass set up bars | A-Pat-Co | General Routing | 5 | 04-18-2007 09:16 PM |
| 1 1/2 Brass guides | MiamiSnookII | Table-mounted Routing | 2 | 01-08-2006 10:06 AM |
| Phillips and Brass screws (tips) | CanuckBeaver | Tools and Woodworking | 15 | 01-12-2005 05:17 PM |
Linear Mode
