| ||||||
It appears you aren’t a registered member of the Router Forums community. Why not spend less than a minute and register for the largest router and woodworking community on the web! Join in over 20,000 discussions with over 40,000 woodworkers. If you’re an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account!| This is a discussion on Ridgid R4511 Table Saw Recall! within the Tools and Woodworking forums, part of the General Woodworking category; Some of you may have this model table saw and should be aware of the ... |
| Replies: 6, Views: 1589
|
New Reply |
| | LinkBack (1) | Thread Tools | Display Modes |
08-18-2009, 07:57 PM
|
 #1 (permalink)
| ||
| Moderation Team   |
Some of you may have this model table saw and should be aware of the recall. The information is available here: http://www.ridgid.com/Download/R4511_PR.pdf It sounds like there is a problem when using a stacked dado set, the blade may come off.  Not good!
__________________ EGO postulo , EGO venalicium , EGO incidere. I measured, I marked, I cut. Latin instructions for firewood. | ||
|
 Sponsor Post
| ||||
 Sponsored Links __________________ This advertisment post is not shown to registered members. Register your free account today and become a member of Router Forums | ||||
|
08-18-2009, 08:45 PM
| #2 (permalink) | ||
| Forum Contributor  |
I'll pass the word on other forums.
__________________ . Never, under any circumstances, combine a sleeping pill and a laxative on the same night. Mike - Retired FoMoCo Tradesman My Gallery @ http://www.routerforums.com/axlmyks-stuff/ | ||
|
|
|
08-19-2009, 01:10 AM
| #3 (permalink) | |||
| Registered User |
Quote:
__________________ John Schaben  "I haven't failed, I have simply discovered several hundred ways that don't work" | |||
|
|
|
Sponsored Advertisements. Register to disable this advertisement.
|
| |
|
08-19-2009, 02:53 AM
| #4 (permalink) | ||
| Moderation Team  Join Date: Mar 2009 Location: Anchorage, Alaska First Name: Jim Posts: 2,737  |
No kidding, John. About the time the shaft came apart and the cutters (hopefully) imbedded themselves in the ceiling like martial arts throwing knives, I'd of lost it!
__________________ Please help keep RouterForums an enjoyable escape by refusing to participate in political discussions. Simply choose to ignore the thread... | ||
|
|
|
08-19-2009, 06:25 AM
| #5 (permalink) | ||
| Forum Contributor |
Or came out the bottom of the saw and did a hop, skip, jump between your legs.
__________________ . Never, under any circumstances, combine a sleeping pill and a laxative on the same night. Mike - Retired FoMoCo Tradesman My Gallery @ http://www.routerforums.com/axlmyks-stuff/ | ||
|
|
|
Sponsored Advertisements. Register to disable this advertisement.
|
| |
|
08-19-2009, 09:06 PM
| #6 (permalink) | ||
| Registered User   |
Really on R4511? I have to check. | ||
|
|
|
08-25-2009, 09:21 PM
| #7 (permalink) | ||
| Registered User |
Thanks for the info. I checked this out with Ridgid and found that saws manufactured during a specific run were affected. My saw was made after the problem was corrected. I feel much better now about using my saw. Thanks again, Fishhwk_1750 | ||
|
|
|
Sponsored Advertisements. Register to disable this advertisement.
|
| |
New Reply |
| Bookmarks |
| ||||||
It appears you aren’t a registered member of the Router Forums community. Why not spend less than a minute and register for the largest router and woodworking community on the web! Join in over 20,000 discussions with over 40,000 woodworkers. If you’re an experienced or beginner woodworker, your questions and knowledge is always warmly welcomed by our community. Register now for your FREE account! 
LinkBacks (?)
LinkBack to this Thread: http://www.routerforums.com/tools-woodworking/15965-ridgid-r4511-table-saw-recall.html | ||||
| Posted By | For | Type | Date | |
| » Ridgid R4511 Recalled: Arbor Shaft Fails, Sends Dado Sets Flying - ToolCrib.com Blog | This thread | Refback | 09-29-2009 09:02 PM | |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
| |
|
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Ridgid Router & Table Plate | mitchmcclary | Table-mounted Routing | 7 | 03-19-2009 03:24 AM |
| Ridgid R2930 (fixed and plunge base routee) | xplorx4 | Tool Reviews | 13 | 03-12-2009 02:20 AM |
| Ridgid Router Easy Above Table Bit Change | shawnpatt | Table-mounted Routing | 1 | 03-06-2009 04:58 PM |
| Ridgid ts3650 Table & router | MickTools | Introductions | 3 | 04-24-2008 02:29 PM |
| Router Table for Ridgid R2930 | RTwitch | Introductions | 2 | 12-26-2007 12:29 AM |
Linear Mode
