| |
| | Register Now!It appears that you aren't a registered member, click below to instantly register and become a member of the RouterForums.com Community! ** Registration removes majority of the website advertisements ** | |
| ||||||
| Tools and Woodworking Mainly for general woodworking questions and comments you may also come here to ask questions, get advice and share your experience with power tools. |
New Reply |
| | Thread Tools | Display Modes |
05-27-2007, 05:53 PM
| #1 |
| Registered User Forum Geek |  Circular Saw and router guide "Off-set" plate Good day I would like to share with you some ideas that made my life easier. The first is, the CS guide, nothing new here except that I used "Floor panels", already covered with Formica and if they give 15 years guaranty for walking on them... They come in two lengths, 50" and 100" (I use the 50"). I use the other side of the guide as a router 10mm (3/8") bit guide. The measuring and positioning method is a little bit different but I find it more accurate. Regards niki  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge If you have 2 or 3 CS's, you can use just a simple straight edge, all you have to make is an "Off-set" plate(s) for each of them. It's better to cut the Off-set plate into 2 (each around 4" or more) to position one at each end of a long board. You can make the same "Off-set" plate also for different router bits.  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge  Click to Enlarge Last edited by Mike; 05-27-2007 at 08:45 PM. |
| Top - Reply with Quote |
 Sponsor Post
| |||
| Advertising
| Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Router Forums | ||
|
05-27-2007, 06:00 PM
| #2 |
| Retired Moderator Supreme Forum King  | Another great post Niki. Thanks for all the photos, excellent ideas! Corey
__________________ My Carving Website: The Iowa Woodcarver http://iowacarver.tripod.com/ My Shop Website - Woodshop 51503 http://woodshop51503.tripod.com/ |
|
| Top - Reply with Quote |
|
05-27-2007, 08:48 PM
| #3 |
| Senior Moderator Supreme Forum King  | This is the third thread on this type of jig, time to make this one a "sticky". Nice job explaining with the photo's Niki, no room for doubt on how to build this very useful jig.
__________________ Mike Please edit your profile with a name and location so we can better assist you. |
|
| Top - Reply with Quote |
|
05-27-2007, 09:19 PM
| #4 |
| Forum Moderator Supreme Forum King  | Niki, You sure know how to keep my brain cells active 
__________________ Cheers, Bob  |
|
| Top - Reply with Quote |
|
05-28-2007, 07:18 AM
| #5 |
| Forum Contributer Supreme Forum King  | How many more of these great ideas have you up you're sleeve Niki? Well done yet again.
__________________ Harry |
|
| Top - Reply with Quote |
|
05-28-2007, 10:40 AM
| #6 |
| Registered User Forum Geek | Thank you so much for your kind words Mike Thank you for "sticking" it...for a moment I thought that I made a mistake... Harry There are a few more but not so many... everyone is limited.... Thanks again niki |
|
| Top - Reply with Quote |
|
11-18-2007, 09:13 AM
| #7 |
| Registered User Sr. Member | The photos that were associated with this discussion thread are no longer available. Any possibility of getting them posted again? |
|
| Top - Reply with Quote |
|
11-18-2007, 09:58 AM
| #8 |
| Registered User Forum Fanatic  | Hi Guys - I'm getting the "Dreaded Red Xs" instead of all the pictures on this post... That's the first time it has ever happened to me at this site. Do any of you PC Gurus have any suggestions? Roger (Roefa)
__________________ Thinking outside the box? What box? |
|
| Top - Reply with Quote |
|
11-19-2007, 07:56 AM
| #9 |
| Forum Contributer Supreme Forum King | No pics. for me either.
__________________ Harry |
|
| Top - Reply with Quote |
|
11-19-2007, 11:20 AM
| #10 | |
| Forum Contributer Supreme Forum King  | Hi Roefa and Harry The RED X is coming from the web site ( photobucket.com) that he uploaded the pictures to ,,,they have close the web site and the pictures are no longer available for viewing. That's why it's best to upload them to the RWS forum... ========== Quote:
__________________ PodCast videos RWS on YouTube http://www.routerforums.com/86898-post1.html Besure and click on the Up Arrow key ▲ on the Youtube video, you can select other youtube videos on router tables  http://www.woodworkingonline.com/?s=dovetail Machine Cut ▼ http://www.woodworkingonline.com/200...cut-dovetails/ http://www.woodworkingonline.com/woo...podcast-store/ http://www.woodshopdemos.com/menu2.htm Bob J. Last edited by bobj3; 11-19-2007 at 11:23 AM. | |
|
| Top - Reply with Quote |
New Reply |
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Linear Mode
