| |
| | Register Now!It appears that you aren't a registered member, click below to instantly register and become a member of the RouterForums.com Community! ** Registration removes majority of the website advertisements ** | |
| ||||||
| Tools and Woodworking Mainly for general woodworking questions and comments you may also come here to ask questions, get advice and share your experience with power tools. |
New Reply |
| | Thread Tools | Display Modes |
10-06-2007, 11:52 PM
| #11 |
| Forum Contributer Supreme Forum King  | Hi Router The one I have is about the same and it runs true. ===============
__________________ PodCast videos RWS on YouTube http://www.routerforums.com/86898-post1.html Besure and click on the Up Arrow key ▲ on the Youtube video, you can select other youtube videos on router tables  http://www.woodworkingonline.com/?s=dovetail Machine Cut ▼ http://www.woodworkingonline.com/200...cut-dovetails/ http://www.woodworkingonline.com/woo...podcast-store/ http://www.woodshopdemos.com/menu2.htm Bob J. |
| Top - Reply with Quote |
 Sponsor Post
| |||
| Advertising
|  Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Router Forums | ||
|
10-07-2007, 02:22 AM
| #12 |
| Registered User Forum King  | plunged all the way, gap on one side or both? |
|
| Top - Reply with Quote |
|
10-07-2007, 10:21 AM
| #13 | |
| Forum Contributer Supreme Forum King | Hi Router If I force it all the way down ,one side is up just by a bit,it looks like about 1/16",the side of the router where the threaded rod was but I have rod in that hole with a clip on it, that hole is now used for the lift kit... If you remove the roll pin and you do get the rod out then what, it looks like the Mfg. didn't want that rod removed once it's put in place.. The only way to change it would be to find some rod and drill a new hole for the roll pin but that maybe a real pain (metric rod) I would look at the top end for the error,,, Something holding it back.....from going all the way down true...maybe by switching the springs around...,or clip that's out of a slot. ? Good Luck with the rework =========== Quote:
__________________ PodCast videos RWS on YouTube http://www.routerforums.com/86898-post1.html Besure and click on the Up Arrow key ▲ on the Youtube video, you can select other youtube videos on router tables http://www.woodworkingonline.com/?s=dovetail Machine Cut ▼ http://www.woodworkingonline.com/200...cut-dovetails/ http://www.woodworkingonline.com/woo...podcast-store/ http://www.woodshopdemos.com/menu2.htm Bob J. | |
|
| Top - Reply with Quote |
|
10-08-2007, 01:09 AM
| #14 |
| Official Greeter Supreme Forum King  Join Date: Sep 2004 Location: New Lebanon, Ohio "USA" First Name: Dave or "Doc" Posts: 4,690  | Bob have you or router is still my name put a: say 1/2" bit it the router and clamped it to a scrap piece of wood and plunged staight down to see if the hole is even all the way around or is elliptical shaped? Just asking.
__________________ Dave the "Doctor" In woodworking there is no scrap, only firewood.  Please edit your profile with a name and location so we can better assist you and make for a friendlier forum. |
|
| Top - Reply with Quote |
New Reply |
| Bookmarks |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 1/4" Collet for Hitachi M12V | RzzB | General Routing | 37 | 05-27-2008 09:11 AM |
| Setting the proper RPM on the Hitachi M12V | jrs4464 | General Routing | 5 | 01-10-2007 10:34 PM |
| Hitachi M12V and Bosch 1619EVS routers | LBrandt | Table-mounted Routing | 3 | 06-03-2006 11:42 AM |
| Hitachi M12V issue | Warren White | General Routing | 4 | 03-23-2005 11:03 PM |
Linear Mode
