Double Sided Tape for Jigs/Fixtures - Page 3 - Router Forums
 14Likes
Reply
 
LinkBack Thread Tools Display Modes
post #21 of 28 (permalink) Old 01-21-2019, 07:39 AM Thread Starter
Registered User
 
Join Date: May 2012
Country: United States
First Name: ben
Posts: 69
 
Default separating taped pieces

Quote:
Originally Posted by JFPNCM View Post
I routinely used the double sided turning tape from Lee Valley to run parts through the TS, planer and router and have not had any issues with residue or parts working loose. I use a razor blade knife to peel one corner of the backing up and the rest peels away easily. The downside, if you use to much of it getting the pieces separated can be tough and it is a bit spendy.
I think the key to separating the two work pieces is to make sure you leave a portion of the perimeter of the two joined pieces with no tape. And, remember where this no tape area is located. I have two old putty knives (unknown origin) that I reach for all the time. The 1" wide knife is thin (~ 1/64" thick) and the 1 1/2" wide knife is thicker (~ 3/64"). Start with the thin knife to create an opening for the thicker knife. Using the two knives in tandem, work you way around the perimeter. It may be slow but I have never had a failure.
Arcola60 and Herb Stoops like this.
bfblack is offline  
Sponsored Links
Advertisement
 
post #22 of 28 (permalink) Old 01-21-2019, 09:22 AM
Registered User
 
Join Date: Mar 2015
Country: United States
First Name: Jim
Posts: 64
 
Default

Ok, thanks, that is how I do it as well.
IRestore is offline  
post #23 of 28 (permalink) Old 01-21-2019, 10:22 AM
Forum Contributor
 
Gaffboat's Avatar
 
Join Date: Mar 2012
Country: United States
First Name: Oliver
Posts: 2,076
 
Default

You could always use the CNCerís tape method that has proven to be very secure. Itís the combination of painterís tape and super glue. The tape is burnished to the backs of the two pieces to be joined, then a few beads of super glue are applied to the tape on one of the parts, and the two pieces firmly pressed together for a few moments. The super glue welds the tape pieces together but the tape is easily removed from the parts when finished, and without leaving a residue. I have also had success using spray adhesive on the painterís tape instead of super glue.
Attached Thumbnails
Click image for larger version

Name:	1 Tape and glue.jpeg
Views:	30
Size:	134.7 KB
ID:	364601  

Click image for larger version

Name:	2 Secured.jpeg
Views:	30
Size:	110.4 KB
ID:	364603  

JFPNCM and Herb Stoops like this.

Dragons slain. Damsels rescued. No reasonable request refused ... unless the dragon's really big.

Simplicity is the ultimate sophistication. ~ Leonardo da Vinci

You can't use up creativity. The more you use, the more you have. ~Oscar Wilde

http://profhenrys.blogspot.com
Gaffboat is online now  
Sponsored Links
Advertisement
 
post #24 of 28 (permalink) Old 01-21-2019, 10:49 AM
Registered User
 
JFPNCM's Avatar
 
Join Date: Dec 2009
Country: United States
First Name: Jon
Posts: 3,643
 
Default

@bfblack

I use a similar approach.

Appreciate the suggestion.

Jon
JFPNCM is online now  
post #25 of 28 (permalink) Old 01-23-2019, 07:28 PM
Registered User
 
Join Date: Jan 2014
Country: United States
First Name: Steve
Posts: 24
 
Default

i use DS tape from amazon, however thrift Or cheap as my says) I use masking tape. I use the whit 3M because is not that much and I use gorilla Gel super glue. Place a strip on masking tape on both surfaces. Add a few drops of sg to on piece of work and press together. It sets fairly quickly and after cutting whatever it is I pull the pieces of wood apart. The tape will let of remove from both pieces and discard.
Steve Pack is offline  
post #26 of 28 (permalink) Old 01-23-2019, 09:47 PM
Registered User
 
Join Date: Aug 2012
Country: United States
First Name: Harry
Posts: 6
 
Default

On the CNC I used 2sided for years then got turned on to painters tape on both the table/spoilboard and the part to be cut. Press both on firmly and and then some CA on the tape with accellerant . Instant bond and ez to remove. Leave tape a little long to be able to lift it.
htasker is offline  
post #27 of 28 (permalink) Old 01-23-2019, 10:29 PM
Registered User
 
Join Date: Jul 2009
Country: United States
First Name: Ellery
Posts: 285
 
Default

I never thought of that method! Thank You to everyone for sharing. I will certainly incorporate that into future practices.
Arcola60 is offline  
post #28 of 28 (permalink) Old 01-23-2019, 10:56 PM
Forum Contributor
 
Herb Stoops's Avatar
 
Join Date: Oct 2014
Country: United States
First Name: Herb
Posts: 7,352
 
Default

I use some I got here on this forum about a year ago.

https://www.routerforums.com/woodwor...late-tape.html

It works great no residue.
Herb
Herb Stoops is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale: Router Double sided Template Tape woodman79 Woodworking Classifieds 35 07-10-2018 05:27 AM
Double sided tape asrubin Table-mounted Routing 11 09-06-2015 06:24 AM
Where in Aus to get double sided tape? darsev Jigs and Fixtures 10 03-12-2012 10:09 PM
double sided tape FEARGI New Member Introductions 4 08-25-2010 09:54 AM
Double sided tape sankarmohan Lobby 16 12-11-2008 10:31 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome