Router Forums - View Profile: IC31
 

IC31 IC31 is offline

Registered User

  About Me

  • My Shop
    Some detailed information about my workshop.
    Power Tools
    JET JTS10 table saw retrofitted with a Delta fence
    Craftsman radial arm saw (#Hp version)
    Miter saw (Low end, but a decent quality)
    Small Craftsman band saw
    Drill press
    Several battery and corded drills, 1/4 - 1/2 inch
    Air compressors (2)
    MIG welder
    Oxy-Acetylene set
    Many Bosch smaller tools
    Sanders, both electric and air
    - and many more small air and electric tools
    My Shop
    The shop is in the basement of my house and is two rooms, both 15x28 feet. One is the mechanical, and the other is the wood/general shop
  • Woodworker Information
    A few details about myself.
    Biography
    Retired from a Dow 50 company after 40 years of working on and building power plants, now just doing what I want along with the requisite 'honey-dos'.
    Location
    Upstate NY
    Interests
    I'm much deeper into street rodding then woodworking at this time, but will probably do some further leaning with what I can do with wood projects. As a family, my wife and I along with our furry friend, Callie the Poodlepup do quite a bit of travel in a 38' Montana High Country 5th wheel camper - and where I am upgrading various parts
    Favorite Router
    I have 3 routers - an ancient Craftsman along with a Porter Cable 7529 and now a Ridgid trim unit. The Craftsman still works well freehand. The P-C, not sure it will have a long survival as it is a Ver.1 and they don't seem to wear well. The small Ridgid router in my 'line up' has had very little use so far
    Woodworking Experience (Years)
    Many
    First Name
    Dave W
    Country
    United States
  • Signature
    Dave W

    Quando omni flunkus, moritati (When all else fails, play dead - R Green)

  Statistics

Total Posts
General Information
  • Last Activity: Yesterday 11:23 AM
  • Join Date: 11-16-2012
  • Referrals: 0

  Friends

Showing Friends 1 to 1 of 1
  • Phil P
    • Phil P is offline

  Mentions

05-03-2020
11:47 PM - Biagio mentioned IC31 in post Ghost Town...
IC31, 1. Guilty as charge...
10:02 PM - Herb Stoops mentioned IC31 in post Ghost Town...
IC31 Dave when I read you...

  Quotes

06-27-2020
11:04 AM - Stick486 quoted IC31 in post Ghost Town...
In my case, a couple hour...
09:02 AM - Herb Stoops quoted IC31 in post Ghost Town...
Running away from civiliz...
05-14-2020
10:43 AM - RainMan 2.0 quoted IC31 in post Ghost Town...
Dan, you are on a roll th...
05-13-2020
10:03 PM - Stick486 quoted IC31 in post Small box joint bit
Got my Whiteside downcut ...
05-12-2020
12:48 PM - graeme.c.payne quoted IC31 in post Ghost Town...
My wife and I have recent...
05-09-2020
02:26 AM - Biagio quoted IC31 in post Ghost Town...
My wife and I have recent...
05-05-2020
10:12 PM - Stick486 quoted IC31 in post Ghost Town...
I like Don Q 151 rum. A b...
05-04-2020
08:07 PM - Stick486 quoted IC31 in post Ghost Town...
Yes, all too well aware o...
05:48 PM - Stick486 quoted IC31 in post Ghost Town...
When did heart surgery be...
05-02-2020
12:01 PM - Stick486 quoted IC31 in post Ghost Town...
Dan, That settle it! We w...
10:46 AM - DaninVan quoted IC31 in post Ghost Town...
Yes, they will do a phone...
05-01-2020
10:34 AM - DaninVan quoted IC31 in post Ghost Town...
Wandered up to my favorit...
04-27-2020
07:45 PM - RainMan 2.0 quoted IC31 in post Ghost Town...
That's what I saw on Satu...
08:15 AM - Stick486 quoted IC31 in post Looking for a "State of Texas" template
I like that cutout - shou...
04-15-2020
01:15 PM - Stick486 quoted IC31 in post Zoom Zoom!
Dan - the way I'm reading...
03-28-2020
09:48 AM - RickKr quoted IC31 in post Replacement miter gauge = junk
...snip... If I had a few...
03-26-2020
10:21 AM - Cherryville Chuck quoted IC31 in post Replacement miter gauge = junk
I'm in the process of doi...
03-23-2020
01:28 PM - Stick486 quoted IC31 in post Replacement miter gauge = junk
Now that the thead has wa...
01:25 PM - Stick486 quoted IC31 in post Replacement miter gauge = junk
Folk - my OP was NOT abou...
03-13-2020
10:19 AM - harrysin quoted IC31 in post Small box joint bit
[QUOTE=IC31;2092731]I did a bit ...
 
For the best viewing experience please update your browser to Google Chrome