Hi!! - Router Forums
 
LinkBack Thread Tools Display Modes
post #1 of 6 (permalink) Old 09-03-2009, 02:30 PM Thread Starter
 
Join Date: Sep 2009
Posts: 1
 
Default Hi!!

I am new. When I use the router in table mounting the bit moves away from the fence. How do I ensure the work piece does not push away from the router bit and mare the piece?
weyburn is offline  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old 09-03-2009, 04:48 PM
Forum Contributor
 
xplorx4's Avatar
 
Join Date: Dec 2008
Country: United States
First Name: Jerry
Posts: 10,671
 
Default

Greetings Ron and welcome to the router forum.

Wisdom: Where experience and knowledge combine and become one.

"We are all one decision away from Stupid!!"

Lamentations 3:22-23

"How often we sacrifice the permanent plans of God on the altar of immediate solutions"

I have a very good memory, just short is all.
xplorx4 is offline  
post #3 of 6 (permalink) Old 09-03-2009, 08:18 PM
Registered User
 
Join Date: Mar 2006
Country: United States
First Name: John
Posts: 1,803
   
Default

Welcome aboard. Your question has a couple of solutions. First you have to make sure your fence is not moving. That means both sides right and left. Figure out how to clamp it down so that it dose not move. Then use feather boards on the out side of the piece you want moulded.
vikingcraftsman is offline  
Sponsored Links
Advertisement
 
post #4 of 6 (permalink) Old 09-03-2009, 08:30 PM
Registered User
 
Join Date: Mar 2009
Country: United States
First Name: Harry
Posts: 282
 
Default

Also be sure you are feeding the work piece the correct direction. right to left if the cutter is between fence and workpiece! Seems different than a hand held, but it isn't.
Harry

Harry, TX
Cut it twice, and it's still too short!
Old_Chipper is offline  
post #5 of 6 (permalink) Old 09-04-2009, 01:08 AM
Forum Contributor
 
Dr.Zook's Avatar
 
Join Date: Sep 2004
Country: United States
First Name: Dave or "Doc"
Posts: 10,715
 
Default

Welcome to the RouterForums Ron.




Dave
the "Doctor"

In woodworking there is no scrap, only firewood.



Dr.Zook is offline  
post #6 of 6 (permalink) Old 09-04-2009, 02:35 AM
Retired Moderator
 
BigJimAK's Avatar
 
Join Date: Mar 2009
Country: United States
First Name: Jim
Posts: 3,503
     
Default

Welcome, weyburn..

Check out that new high-tech cordless router.. wireless and no recharging required!!
BigJimAK is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome