New to the forum - Router Forums
 
LinkBack Thread Tools Display Modes
post #1 of 6 (permalink) Old 03-28-2010, 07:57 AM Thread Starter
Registered User
 
Yellow Hammer's Avatar
 
Join Date: Mar 2010
Country: United States
First Name: Bob
Posts: 3
 
Default New to the forum

Hello from Yellow Hammer, a died-in-the-wool Alabama Crimson Tide football fan and sometimes woodworker. I look forward to participating here. As I was surfing this morning, I ran across this forum and decided I needed to join rather than be just a spectator. I recently bought the Incra LS17 positioner for my router table and had to modify my existing conventional table. I also recently replaced my Hitachi M12V with the PC 7518. Yesterday, after spending a frustrating day in my shop and unable to get consistent and repeatable results cutting sliding dovetails, I discovered movement in my old router lift. I had been looking at the Incra Woodpecker PRL-V2 for sometime, and yesterday, bit the bullet and ordered it. Now, I have decided to build a new router table to accommodate the positioner however, I have been unable to find any suitable plans that will work with the Incra.

Does anyone have suggestions or ideas for a router cabinet that will accommodate this beast. By the way, I absolutely love this Incra system!
Yellow Hammer is offline  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old 03-28-2010, 09:20 AM
Retired Moderator
 
TwoSkies57's Avatar
 
Join Date: Feb 2009
Country: United States
First Name: Bill
Posts: 6,019
   
Default

Bob.....

welcome on board...

1st link is an excellent assortment of different tables..
http://www.routerforums.com/table-mo...our-table.html

2nd link is my table...making use of the LS17/Incra lift/wonder fence....
http://www.routerforums.com/table-mo...ble-setup.html

let the sleepless nights begin..*S*
TwoSkies57 is offline  
post #3 of 6 (permalink) Old 03-28-2010, 10:39 AM Thread Starter
Registered User
 
Yellow Hammer's Avatar
 
Join Date: Mar 2010
Country: United States
First Name: Bob
Posts: 3
 
Default

Bill, really cool table! What material is your top made of?
Yellow Hammer is offline  
Sponsored Links
Advertisement
 
post #4 of 6 (permalink) Old 03-28-2010, 12:28 PM
Retired Moderator
 
TwoSkies57's Avatar
 
Join Date: Feb 2009
Country: United States
First Name: Bill
Posts: 6,019
   
Default

Bob.

Thank you...

Top is a 1 3/8" thick mdf core with a phenolic laminate on top and bottom. Tabletop was custom made to my specs by Woodpeckers. I have to say they did a fantastic job...were great to work with and answered a good dozen emails I had with questions..
TwoSkies57 is offline  
post #5 of 6 (permalink) Old 03-28-2010, 09:16 PM
Forum Contributor
 
xplorx4's Avatar
 
Join Date: Dec 2008
Country: United States
First Name: Jerry
Posts: 10,671
 
Default

Greetings Bob and welcome to the router forum. We are pleased you have chosen to join with us.

Wisdom: Where experience and knowledge combine and become one.

"We are all one decision away from Stupid!!"

Lamentations 3:22-23

"How often we sacrifice the permanent plans of God on the altar of immediate solutions"

I have a very good memory, just short is all.
xplorx4 is offline  
post #6 of 6 (permalink) Old 03-28-2010, 11:34 PM
Forum Contributor
 
Dr.Zook's Avatar
 
Join Date: Sep 2004
Country: United States
First Name: Dave or "Doc"
Posts: 10,715
 
Default

Hello Bob, and welcome to the RouterForums. Glad to have you aboard.




Dave
the "Doctor"

In woodworking there is no scrap, only firewood.



Dr.Zook is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Old to Woodworking - New to the Forum rwhpi1 New Member Introductions 3 07-26-2010 10:16 PM
2007 Forum Contributer Nomination Thread! Mark Site Help and Suggestions 19 04-13-2007 08:33 PM
[8/26/2006] Forum Contributer Nomination Thread Mark Lobby 42 09-16-2006 01:41 PM
[8/26/2006] New Forum Contributer Rank Mark Site Help and Suggestions 0 08-26-2006 05:43 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome