Router Forums - Reply to Topic
Thread: insert plate counter sinking Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-07-2009 04:31 AM
awoodnut
Got R Done

Thanks guys

I got the points on for marking with the drill and got it all together. Had to drill for the above tabel height adjustment also.

I was going to drill for the shaft lock but decided not to as it is so close to one of the mounting screws on this Freud 1700 I got from HD.

Did some practice dados and it works slick. First project is a hat rack for the wife and the small shelf will be set in a dado. I am thinking I may try to make a crown molding to go under it for extra strength. I will post a pic when I get it put together.

Need to get a vacume hooked up to it quick, sawdust all over the shop.
06-05-2009 03:24 AM
derek willis A drill used for cutting steel etc. not wood.
06-04-2009 10:35 PM
awoodnut
Thanks

Thanks

I will get it mouted tonight or this Saturday.

What is an enginearing drill? I just have a good quality fractional drill index I use for work.

Mike R
06-04-2009 11:08 AM
bobj3 HI Mike

I just stick them in the drill chuck,the chuck is make to hold round things and it will .. and it will not damage the threads..

I make them all the time but I use all thread rod most of the time.
see below, the ones below are bigger but it's done the same way..

======
Quote:
Originally Posted by awoodnut View Post
Thanks BobJ

I got the longest ones they had at Ace. In this diamiter they are just small.

Do you stick them in the drill and chuck the threads or do you put a nut on them?

Mike R


06-04-2009 09:17 AM
derek willis Just use a sharp engineering drill about 1/2" dia for countersinking.
06-04-2009 12:34 AM
awoodnut
thanks

Thanks BobJ

I got the longest ones they had at Ace. In this diamiter they are just small.

Do you stick them in the drill and chuck the threads or do you put a nut on them?

Mike R
06-03-2009 11:39 PM
bobj3 Hi Mike

Just put the set screws in battery pack drill and put a point on the them with grinder/belt sander it just takes a sec. or two...
But I will say it's best to pickup some longer ones and them put a sharp point on them and then just use the ones you have now...(longer ones from ACE hardware for 10 cents.each.
Is it even that critical ? no, almost all counter sink holes are 82 deg..so you can use just about anything you have on hand ..


========


Quote:
Originally Posted by awoodnut View Post
Hi Guys

I finally got all my stuff to mount the router. Got a Roussue centering kit to make it easy I thought....no such luck. Got the wrong kit and the screws and marking pinns are to big. Did get a better understanding of what I was doing from looking at the parts.

Went and bought screws and set screws to fit my Frued router. Now for the question.

The set screws are not sharp, I think I can get a mark well enough without sharpening a point on them but is there a simple method for sharpening the little buggers. They are a metric D 4 I think it was.

Also the roussue centering kit called out an 80* countersink bit for the screws in the kit. How do I determine what countersink to use with the screws I got? Is it even that critical?

They look about the same as the ones in the kit but my micrometer eye could be out of whack.

Thanks for the help


06-03-2009 11:28 PM
awoodnut
insert plate counter sinking

Hi Guys

I finally got all my stuff to mount the router. Got a Roussue centering kit to make it easy I thought....no such luck. Got the wrong kit and the screws and marking pinns are to big. Did get a better understanding of what I was doing from looking at the parts.

Went and bought screws and set screws to fit my Frued router. Now for the question.

The set screws are not sharp, I think I can get a mark well enough without sharpening a point on them but is there a simple method for sharpening the little buggers. They are a metric D 4 I think it was.

Also the roussue centering kit called out an 80* countersink bit for the screws in the kit. How do I determine what countersink to use with the screws I got? Is it even that critical?

They look about the same as the ones in the kit but my micrometer eye could be out of whack.

Thanks for the help

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome