Router Forums - Reply to Topic
Thread: Bosch router table starter pin Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-05-2019 10:08 AM
harrysin I realise that this is an old thread but there is a far better way than a pin, THE FENCE, all tables have one.
06-05-2019 12:17 AM
gdonham1 Glad you figured it out. One more suggestion would be to get a plastic spacer you could put over the bolt. The plastic sleeve would protect your project from a dent in it. The starter and/or safety pin is to keep your project from spinning out of control when the wood is feed into the router bit. Sometimes you get the start of the spin and the starter/safety pin prevents the out of control but the work does slam into the pin.
06-04-2019 08:00 PM
gen
Bosch fulcrum pin

Quick and inexpensive solution (the best one is to purchase a bold as indicated by one of the contributors below): but if you want a substantial post not a thin bolt, you can do the following. Purchase the 4/20 fulcrum pin from Rockler for $4.99--they will send you two pins in the pack. Take one and gently thread it into one of the holes that is at about 2 O'Clock in the Bosch router table insert plate, taking your time to do a quarter turn, then a half turn, and then reverse it, and then continue again proceeding by quarter turns and reversing after about 1/2 to 3/4 of a turn until you have rethreaded the entire hole to suit the Rockler 4/20 fulcrum pin. A little patience with your vice grips and within 3-5 minutes you are done because the aluminum table top is really quite soft. Then you are left with one pin with a few rough marks from the vice grips and another that is perfect! They will both work quite well.
08-16-2017 02:32 PM
DaninVan Laughing because I just realized Tom Googled my spelling!
08-16-2017 02:30 PM
DaninVan What can I say, Tom; we speak and spell the Queen's English up here.
08-16-2017 02:04 PM
DesertRatTom SPELT (got my curiosity up):

noun
1.
one of the earliest cultivated forms of wheat, Triticum aestivum spelta, native to southern Europe and western Asia, used for livestock feed and as a grain for human consumption.

verb (used with object), spelled or spelt, spelling.
1.
to name, write, or otherwise give the letters, in order, of (a word, syllable, etc.):

verb (used without object), spelled or spelt, spelling.
1.
to name, write, or give the letters of words, syllables, etc.:
He spells poorly.

origin: before 1000; Middle English, Old English from Late Latin spelta, probably from Germanic; compare Old High German spelza (German Spelt)

Haven't seen this word used in decades. Perfectly legitimate word, just a rarity that stirred my curiosity.
08-16-2017 01:54 PM
DesertRatTom
Quote:
Originally Posted by DaninVan View Post
...Buy a nut as well; run it up the thread before you make the cut, then run it back down and off...it'll 'chase' the cut portion so you don't damage the threaded hole in the deck.
Dang, you fellas is smart!
This solves a minor irritation whenever I cut a bolt or threaded rod down; getting the thread to start in the nut after chopping it off.
08-15-2017 12:16 AM
Stick486
Quote:
Originally Posted by DaninVan View Post
You spelt 'accessories' incorrectly...
and???
08-14-2017 11:30 PM
thomas1389
Quote:
Originally Posted by DaninVan View Post
'Cause as everyone knows, the spares will be right there when you need one; no searching through stuff...
Yeh, right.
08-14-2017 10:29 PM
DaninVan You spelt 'accessories' incorrectly...
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome