|Topic Review (Newest First)|
|10-13-2017 11:18 PM|
I wonder if the XP6000 is going to become the ugly step child of the Makita line-up. |
There’s seven new blades being designed to expand the functionality of the XPS01PTJ. They fixed several problems people complained about in the design of the XP6000. The XPS01PTJ cordless has a better handle, better dust port design, improved egonomics better knobs, and a smoother plunge.
Makita has zero plans to do anything to fix or improve the XP6000 design. None of new high performance blades will be designed to work with the XP6000. All the new blades will be exclusive to the X2 platform based XPS01PTJ.
It’s kind of annoying but I guess you can’t sell battery upgrades for the XP6000.
|10-05-2017 02:02 AM|
|DesertRatTom||Love all the usage suggestions. Creative bunch.|
|10-04-2017 10:09 PM|
|Everend||Right, it slides under the fence and sometimes rides up the blade and jumps. That's how I started this project. Then part way through I remembered I had a track saw, I put down that piece of plywood, set the blade to 1/8" so it only minimally scored the plywood under the laminate. Cut it very clean! I also used clamps to hold the track to the plywood, sandwiching the laminate between the track and the plywood. It worked very well!|
|10-04-2017 09:58 PM|
Originally Posted by Everend View Post
|10-04-2017 06:29 PM|
|Everend||It also worked very well for trimming laminate to rough size before applying the contact cement.|
|10-04-2017 06:27 PM|
|Everend||I found a new use for my track saw today. Shaving the edge off a elect plate that is in the way of the new counter I just finished.|
|09-30-2017 06:53 PM|
|Steven Owen|| |
Originally Posted by tomp913 View Post
|09-30-2017 03:31 PM|
Originally Posted by Steven Owen View Post
Their EZ Ready Makita® 5008MGA Circular Saw with an 8-1/4" blade (listed at $299 for the saw only) has an off track depth of cut of 2.5 inches at 90 degrees. With base on track the depth of cut is 2 1/8 inches at 90 degrees.
The EZ Ready saws come with the Smart Base, front dust ports, and flexible plastic dust shields added. I have two at this point - the Hitachi and the Makita MGA5007. If you want to save a few bucks and buy the saw and install the Smart Base yourself, you can do that. For the larger saw you might want to call Eurekazone.com to make sure you're getting the right base. I know the standard Smart Base fits on most circular saw, but not sure about the real big one.
The guide rails (tracks) come in several lengths, but I would suggest a 64" guide rail for most uses (it provides a "launch pad" for the saw, plus the 48" to cross cut plywood), and then add a 54" guide rail if you want to have an 8 foot cut length:
32" guide rail: $75, 54" guide rail: $112, 64" guide rail: $132, 72" guide rail: $149. The guide rails come with sized plastic anti-chip edges that provide clean cuts on the guide rail side of the kerf. The anti-chip insert on the Smart Base provides a clean cut on the non-guide rail side of the kerf. This youtube.com video shows how the anti-chip rails provide clean cuts and how the fin insert prevent kickback on off-rail cuts:
You'd also want a set of two regular EZ Smart Clamps ($28), and, if you want to connect two tracks you'll want a set of two outside channel guide rail connectors ($30) per joint. If the total length of combined tracks is more than 110" you'll want to add a center channel guide rail connector ($14) per joint.
BTW, I have no financial connection to Eurekazone - except that I've been using their guide rails and accessories since 2008 - when I'd all but given up on being able to safely cut plywood. I'd lowered myself to using a jigsaw and a hand saw - honestly!!
|09-30-2017 12:06 PM|
|tomp913||Finally got back out in the shop and had to cut the bottom for a pull-out shelf, thought I'd post these photos of the cut my Makita made on a piece of 1/2" birch plywood - standard Makita blade that came with the saw, the offcut edge is to the right, just like the first photo, cut with the "good face" down (force of habit). I bought the plywood at HD so it's probably not A1 grade, but more than good enough for a drawer bottom. I've been pretty satisfied with the cut I've been getting with this saw - the Makita blade actually gets pretty high scores in the reviews that I've read. I'll see how it holds up to some more use before deciding whether I need to spend the money for an Infinity blade.|
|09-28-2017 11:19 AM|
I posted my review in a separate thread, but thought I'd repost it here as well. I also get to clean up some spelling goofs here. |
After a couple of weeks delay, here's the promised review of the Triton plunge/track saw, Model TTS 1400. I purchased this on sale about a month ago from Rockler. I also purchased the 59 inch long track for it and the two, 27 inch short tracks, since I wanted sufficient length to cut 5 ft sq BB ply.
First step was replacing the stock blade with a 165 mm Infinity purpose built blade. This had a slightly wider kerf than the Triton and the carbide teeth look to be slightly wider and noticeably thicker for potentially more sharpenings. Replacement was easy. There is a small switch with two overlapping circles beside the top of the plunge handle. This is the setting for changing blades. Press down on the handle and the blade goes down just far enough to reveal the bolt and washer that hold the blade on. The saw clicks and holds this position until you are finished. Slide the blade out the bottom slot, slide the new blade in, put the washer and bolt back in and tighten. There is a push button that when pressed in, locks the blade so it won't rotate. A handy item is that the Allen wrench used to loosen/tighten the bolt fits in an opening in the upper handle so you won't lose it.
Next order of busines was connecting one short track to the long one, since you must trim the rubber hold down strip before first use. I was disappointed to discover that one of the short tracks did not quite line up with the long track, in fact, this raised portion caused the saw to hang up slightly when passing the joint. I will see about a replacement. The other segment lined up correctly. Be sure to get the alignment right before tightening the set screws on the connectors. The connectors are two strips so the set screws engage the top and bottom of the two T tracks into which they fit. There is a very tiny bit of play that will permit you to align the two tracks before cinching them down tight with the supplied allen wrench. I stowed the wrench in the instruction book, otherwise I'll surely lose track of it.
You trim the edge using the scoring setting. The same switch that allows changing the blade has a second circle symbol with a line drawn through the edge of the circle for the scribe cut setting. This limits the plunge to about 3/16ths below the track. I did this with two 2x4s set side by side. The scribe cut was clean and crisp. This produces a nice clean edge on the rubber. The anti friction tape on the tracks did their job so sliding the saw was smooth and easy. You must turn the anti kickback knob on the side of the saw's base to allow it to slide backwards on the track.
The knobs... The blade side of the saw contains several settings. The trunion adjustment allows setting the blade angle anywhere from 90 to about 48 degrees. Very solid and seems to be precise. There is a depth of cut limiting knob that you set so the teeth just clear the workpiece. I think I set it to go too deep, so as the teeth came up out of the workpiece, it tore out fine splinters in the outside. The cut was very clean under the rubber hold down side.
If you look at the pictures, you'll see several strips cut from the same piece of BB ply. The top edge is the roughest and was cut with my DeWalt 18v circular saw with a fairly fine blade. It was the exit side of the cut. The middle narrow strip shows the tearout from the Triton on the unprotected edge. This ply has been sitting in our very dry weather for months and I think that contributed to the problem. The third strip was cut with the Triton with blue tape on the edge and has almost no tearout. Blue painter's tape will be a regular thing for me. I think I also need to reduce the depth of cut so the whole gullet isn't visible below the workpiece. A shallower angle slice might help with tearout. The only problem edge is the one not supported where the blade exits. All other edges are very clean. I have not tried a piece of melamine, so I can't comment on chip out. I suspect that with the Infinity blade, scribing and keeping the good side down, it will be slight
Dust collection was quite good. The picture shows the residue after 3 cuts. The DC port happened to fit into a hose I got from Lowes. I'll be using some of Rockler's stretchy tape to seal this a little better, but there was no dust flying around at all. My hose terminates in a 4 inch connector that fits into my HF DC unit. I use the same setup to clean out my table saw, but I'll keep the hose in the garage shop with the track saw. I was expecting mediocre performance on DC, so this was a very pleasant surprise.
It takes a little while to figure out what all the knobs do, but they mostly have to do with fitting the saw tight to the track. There are holes at the end of each track so you can hang them up, out of harm's way.
Power on this saw seemed to be a little light. You will want to let it run up to speed before plunging, then let it wind to a stop before lifting the saw off the track. It is close to 10 lbs, and if I had to lift it all day long, it would be unpleasant. If I were doing construction, expecially finish work, I'd pop for the Festool, but for my purposes the Triton TTS1400 is a very nice choice
Over all, I'd give this an 8.5 to 9 on a scale of 10. Worth the near $500 I paid for the whole kit and kaboodle. But I will definitely be using painter's tape or scoring cuts with it for best results.
Nice to get back in the shop again. And this is much easier to read than the original. Good writing is all about editing.
|This thread has more than 10 replies. Click here to review the whole thread.|