Router Forums - Reply to Topic
Thread: Incra master lift Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
04-29-2019 08:09 PM
DesertRatTom My router fence has a safety shield that I don't always use, but it partially encloses the bit which will restore some of the air flow to the DC port behind the fence. The one shown is a Jessem and requires a fence with a T-track. Theoretically you could add an extension (Lexan) so you could keep the fence further away, or even a DC port through the shield, directly above the bit. As an alternative, you could make a shop built unit. It would not help with DCwhen cutting a stopped or full dado.

Here are a couple of sources

This one is tinted orange but is only $7: https://www.amazon.com/Router-Bit-Gu...09&s=hi&sr=1-7

A little smaller kind of yellow tint, about $6: https://www.amazon.com/Router-Bit-Gu...556582317&s=hi

JessEm's clear bit guard in the pix is available direct from the company, about $10: https://jessem.com/products/bit-guar...e-mast-r-fence
04-29-2019 05:29 PM
tulowd
Quote:
Originally Posted by sreilly View Post
My suggestion as well. In fact you can call and speak to Mark at 1.888.804.6272.

That said while I don't have the Incra lift I do as Herb and have DC at both the fence and lift areas that do an outstanding job. That said I should mention that I have a CV1800 6" DC system and the 6" port feeds a single inlet with 2 - 4" blast gates, one for the fence and the other for the lift compartment. DC makes all the difference.
That is the same table and fence I have, sweet mod on running another extrusion for separating the micro adjuster. Love the stand, that is nicer than the furniture in my meager existence. Tip o' the hat to you, good sir.

I have similar D/C setup as yours, along with a table top dust hood as well. Hoping to start using it soon, once the D/C is connected and everything else is built. The clear router cabinet has 2 blast gates in it to control air flow.
04-29-2019 09:45 AM
grbmds
Dust Collection in the Fence

Dust collection using the port on the Incra Wonder Fence does improve the result, but only when the bit is near or partially buried in the fence. If the bit is completely exposed connection to the fence port is of no use in dust collection.

The slotted throat plates that Incra sells improve downward airflow significantly. They are called the CleanSweep Magnalock Rings.
04-26-2019 10:49 PM
DesertRatTom Stick has suggested using a snorkle attached to the bottom of the router to improve upward air circulation through the router, to cool the motor. But his would also improve the up-flow through the insert and possibly improve above the table DC.

And, that is a really handsome router table!
04-25-2019 08:28 AM
sreilly
Quote:
Originally Posted by gdonham1 View Post
I dont have the Incra Lift but really like Incra Products. Why dont you email support at Incra and ask them about the problem. They have always been very helpful when I contacted them in the past. The Incra staff is small and know their products.

[email protected]
My suggestion as well. In fact you can call and speak to Mark at 1.888.804.6272.

That said while I don't have the Incra lift I do as Herb and have DC at both the fence and lift areas that do an outstanding job. That said I should mention that I have a CV1800 6" DC system and the 6" port feeds a single inlet with 2 - 4" blast gates, one for the fence and the other for the lift compartment. DC makes all the difference.
04-24-2019 01:28 AM
gdonham1 I dont have the Incra Lift but really like Incra Products. Why dont you email support at Incra and ask them about the problem. They have always been very helpful when I contacted them in the past. The Incra staff is small and know their products.

[email protected]
04-23-2019 11:48 AM
hawkeye10
Quote:
Originally Posted by Herb Stoops View Post
I use the inserts that are larger than the bit to allow air flow through the table besides through the fence. I have the DC wyed to the box below and to the fence.

Herb
Having dust collection on the fence and from below really helps.
04-22-2019 11:34 PM
Herb Stoops I use the inserts that are larger than the bit to allow air flow through the table besides through the fence. I have the DC wyed to the box below and to the fence.

Herb
04-22-2019 10:42 PM
grbmds Over time, dust and chips do build up on the router and lift mechanism under the Incra table even with the Cleansweep box installed. I would suspect that the previous poster who answered is correct that inadequate dust collection has something major to do with your problem. I always attach the CleanSweep port to my cyclone dust collector instead of the vac I own. The vac, even though one of the best, just doesn't generate enough air volume movement to such the dust right through.

I do get dust buildup on the router lift threads and mechanism but only over a longer period of time. The router lift and router should be pulled out periodically for cleaning maintenance. However, this should not be a problem each time you use it.

Do you use the Incra recommended slotted throatplates with the lift? They improve the air flow a lot and don't interfere with use.
04-22-2019 09:56 PM
Stick486 your DC is inadequate and/or the air flow for the DC isn't set up as well as itcould be..
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome