A.G.E. Series by Amana Tool MD502 Raised Panel Door set - Router Forums
 2Likes
  • 2 Post By Cherryville Chuck
 
LinkBack Thread Tools Display Modes
post #1 of 6 (permalink) Old 05-23-2016, 10:51 PM Thread Starter
Registered User
 
Join Date: Jan 2015
Country: United States
First Name: Eugene
Posts: 59
 
Default A.G.E. Series by Amana Tool MD502 Raised Panel Door set

Does anybody know how far the rail protrudes into the stiles on this set, it makes a 3/8 Grove, i measured from the tip of the cutter to the bearing and it appears to be 3/8 as well, I can't find the information in the kit or on there site? I just wanted to make double sure before I begin to cut things up, and come up too short when I do the coaping cuts, thanks for the anticipated help.
Eugd is offline  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old 05-23-2016, 11:11 PM
Moderation Team
 
Cherryville Chuck's Avatar
 
Join Date: Sep 2010
Country: Canada
First Name: Charles
Posts: 14,856
 
Default

Eugd it should be the distance from the tip of the largest diameter to the bearing. I tried finding that set on their site but it didn't come up in a search.

Someone I consider a master woodworker once told me that a master woodworker is not someone who never makes mistakes. He is someone who is able to cover them up so that no one can tell.
Cherryville Chuck is online now  
post #3 of 6 (permalink) Old 05-23-2016, 11:48 PM
Moderation Team
 
Cherryville Chuck's Avatar
 
Join Date: Sep 2010
Country: Canada
First Name: Charles
Posts: 14,856
 
Default

It wouldn't hurt to try them on some scrap first and then you can use those for dummy sticks to set the production run with. Then you'll be able to make sure before you make a mistake on some expensive wood.
David Dickson and cocobolo1 like this.

Someone I consider a master woodworker once told me that a master woodworker is not someone who never makes mistakes. He is someone who is able to cover them up so that no one can tell.
Cherryville Chuck is online now  
Sponsored Links
Advertisement
 
post #4 of 6 (permalink) Old 05-23-2016, 11:56 PM
Retired Moderator
 
Mike's Avatar
 
Join Date: Nov 2004
Country: United States
First Name: Mike
Posts: 11,921
 
Send a message via Skype™ to Mike
Default

You should follow Chuck's very good advice and build a couple samples from cheap material. I make prototypes for most of my projects.

Mike
"Living in the D" (this means Detroit!)
"It's fine to disagree with other members as long as you respect their opinions"

Last edited by Mike; 05-23-2016 at 11:59 PM.
Mike is offline  
post #5 of 6 (permalink) Old 05-24-2016, 03:55 AM
Forum Contributor
 
Stick486's Avatar
 
Join Date: Jan 2013
Country: United States
First Name: Stick
Posts: 24,511
 
Default

Quote:
Originally Posted by Eugd View Post
Does anybody know how far the rail protrudes into the stiles on this set, it makes a 3/8 Grove, i measured from the tip of the cutter to the bearing and it appears to be 3/8 as well, I can't find the information in the kit or on there site? I just wanted to make double sure before I begin to cut things up, and come up too short when I do the coaping cuts, thanks for the anticipated help.
your best bet would be to run a few test cuts and assemblies w/ scrap material...

This would have been the week that I'd have finished chewing thru the restraints...
If only new layers hadn't been added....

Stick....
Forget the primal scream, just ROAR!!!
"SNORK Mountain Congressional Library and Taxidermy”
Stick486 is online now  
post #6 of 6 (permalink) Old 05-24-2016, 05:15 AM Thread Starter
Registered User
 
Join Date: Jan 2015
Country: United States
First Name: Eugene
Posts: 59
 
Default

Will do, thanks gentlemen
Eugd is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
peak hp vs. real hp danapointed New Member Introductions 15 05-10-2017 03:33 PM
Craftsman v. Delta Tablesaws Thowie70 Tools and Woodworking 22 02-24-2014 10:12 PM
Peak HP dgcutter General Routing 22 01-10-2013 08:23 PM
Selecting the Correct Router Bit LMT Onsrud (Onsrud) Router Bits - Types and Usage 1 02-07-2012 11:17 PM
square corner cnc raised panel Bob flan CNC Routing 28 06-11-2011 04:04 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome