Flash! Contest extended - Router Forums
 
LinkBack Thread Tools Display Modes
post #1 of 2 (permalink) Old 07-30-2009, 11:33 PM Thread Starter
Retired Moderator
 
Mike's Avatar
 
Join Date: Nov 2004
Country: United States
First Name: Mike
Posts: 11,921
 
Send a message via Skype™ to Mike
Default Flash! Contest extended

Many forum members did not know that there is a contest running. The rules are simple: build a plaque which is 5-1/2" x 7-1/2" x 3/4" thick from either Ash, African Mahogany or Lyptus. The top edge needs a roundover and the bottom needs a cove cut to create a shadow line. Other than that the sky is the limit. There are prizes for the best design, but you can also win a prize by discussing the diferences in the way the woods are machined. You must build your own plaque and submit a photo of it to enter. These woods are available from many sources but our member and friend Keith at The Woodworkers Source is offering a special project pack with enough wood to make 3 plaques of each type of wood.
To be fair to all forum members this contest has been extended until August 31st, 2009. There are nine prizes, the least of which is a $25 gift certificate for Oak Park, the home of The Router Workshop. I bought one of the project packs and split it with Rob (SNRGRAILROAD) and James (JW2170). So the three of us will each be submitting 3 entries. Everyone has a very good chance to win, why not enter? Unless of course you would prefer that the three of us split all the prizes...
See the details here: http://www.routerforums.com/forum-co...tml#post115331

Mike
"Living in the D" (this means Detroit!)
"It's fine to disagree with other members as long as you respect their opinions"
Mike is offline  
Sponsored Links
Advertisement
 
post #2 of 2 (permalink) Old 07-31-2009, 07:18 AM
Forum Contributor
 
AxlMyk's Avatar
 
Join Date: Jun 2006
Country: United States
First Name: Mike
Posts: 3,165
   
Default

I guess the whole thing doesn't make sense to me. Especially this part.
Quote:
piece of material that has a 1/4” round over profile routed on the two edge and two ends of the front face then the router bit is changed to the 1/4” Cove bit and route the cove profile on the two edges and two ends of the back face.

.
Never, under any circumstances, combine a sleeping pill and a laxative on the same night.

Mike - Retired FoMoCo Tradesman
My Gallery @ http://www.routerforums.com/axlmyks-stuff/
AxlMyk is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
RouterForums.com - 2008 Holiday Contest Mark Contests Archive 36 01-25-2009 03:30 PM
RouterForums.com Holiday Contest! Mark Contests Archive 75 01-23-2007 07:59 PM
New Contest Ideas Mark Site Help and Suggestions 22 11-23-2006 06:37 PM
Start your own contest! Mark Forum Contests 0 09-28-2006 08:46 PM
RouterForums.com December 2005 Contest - VOTE NOW!! Mark Contests Archive 12 02-03-2006 10:13 PM

Posting Rules  
You may post new threads
You may post replies
You may post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome