Cutting Vinyl Strip - Router Forums
 
LinkBack Thread Tools Display Modes
post #1 of 1 (permalink) Old 07-30-2017, 08:51 PM Thread Starter
Registered User
 
Join Date: Mar 2014
Country: United States
First Name: Tom
Posts: 1,423
 
Default Cutting Vinyl Strip

I needed to cut a piece of vinyl trim down to make an anti-chip edge for the rail on my track saw - the installed strip is shown in the first photo below. The strip now gets trimmed by the saw and provides both an indication of the cut line and an anti-chip feature.

Basically two simple operations - a pass on either side of the strip on the table saw to provide grooves for the vertical legs of the opening and then a pass on either side of the strip on the router table to reduce the thickness to fit the height of the groove.

All was going well until the first pass on the router table to reduce the thickness - ran the first strip through on both faces, looked at it and saw that the router had taken most of the thickness down to the bottom of the kerf. A second look at my set-up - the second photo - and I immediately saw what I'd done wrong. The feather boards are in the way, hiding the fact that I'd neglected to think what the feather board was going to do to the flexible (1-1/4" wide x 12 mm thick) strip of vinyl, which was to push it into the 2" dia. hole in the router plate. An hour later (I just knew that I had seen it somewhere) and I had found and installed the adapter ring made to accept P-C bushings, with a brass bushing to close up the clearance around the router bit. I thought that the original feather board set-up would be OK but, just to be sure, moved them to cover just the infeed part of the cut.

Haste makes waste.

I wanted to use my MagSwitch feather board assembly from the TS on the router table, but the cast iron plate was too small and the magnets didn't hit it. The MagSwitch set-up is one I made to cut edge grooves in door rails and stiles for plywood flat panels. I needed to be able to hold the parts against the fence and down on the table at the same time, and the standard MagSwith parts wouldn't let me so I came up with the idea of adding the four standoffs - normally use it with 2-1/4" wide rails on edge, bit it worked just as well with these thin strips.
Attached Thumbnails
Click image for larger version

Name:	IMG_4906.JPG
Views:	103
Size:	426.1 KB
ID:	290777  

Click image for larger version

Name:	IMG_4891.JPG
Views:	92
Size:	468.5 KB
ID:	290785  

Click image for larger version

Name:	IMG_4893.JPG
Views:	89
Size:	447.8 KB
ID:	290793  

Click image for larger version

Name:	IMG_4894.JPG
Views:	82
Size:	417.8 KB
ID:	290801  

Click image for larger version

Name:	IMG_4888.JPG
Views:	91
Size:	434.1 KB
ID:	290809  

tomp913 is online now  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Table saw long piece cutting jig Dejure Jigs and Fixtures 2 06-13-2016 11:54 AM
dado blade for spline joining sjonesphoto Tools and Woodworking 34 03-11-2014 11:11 AM
A suggestion from Maurice harrysin Woodturning and Lathes 48 12-08-2013 09:16 AM
Cutting out Circles and Arcs the Easy Way learnexperience Portable Routing 1 11-26-2011 01:29 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome