Router Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-14 of 14 Results
  1. Jigs and Fixtures
    I was always fascinated by the Router Crafter, and happened on an essentially new one at a good price a while back, bought it and put it in storage until I can build a bigger shop (hopefully this year). I have ZERO time using it. Anyway, I'm looking at upgrading my router (I have a PC 693PK with...
  2. New Member Introductions
    God Afternoon. I am John from Port Hope, Ontario. I have two lathes a Oneway 2026 and a jet and teach wood turning. I just bought a router Crafter and a CNC machine which I have to learn how to use.
  3. General Routing
    i have a router crafter i purchased and have been using to turn flutes i just picked up the drive spindle part off ebay and noticed that it tends to move a bit more than it should after a closer look i noticed my crafter is missing the lock ring on the back of the cable spindle part number...
  4. General Routing
    I have inherited a craftsman router crafter tool. I am trying to find a complete Owners Manual for it.. Any help would be appreciated. Thanks, Foxyoldman.
  5. General Routing
    I have inherited a craftsman router crafter tool. I am trying to find a complete Owners Manual. any help would appreciated.. Foxyoldman
  6. Show N' Tell
    A friend of my Mother's saw one of the canes I made using the router crafter and asked me to make one as a birthday gift for an elderly friend of her's. After I made it i felt the end wasn't sturdy enough so I got some copper tubing and put that over the wood with 15 minute epoxy. The wood is...
  7. Show N' Tell
    Was at a craft show a few weeks back with some canes for sale and a scoutmaster asked if I did staffs. I told him I hadn't but would give it a try. Since the lathes and the router crafter can't take more than about 36 inches I had to make it in two pieces. Of course, since the stock i used is...
  8. New Member Introductions
    Howdy all, I found the forums because it was the first hit when I googled "rout-a-signer". Too bad in 10 pages of post I never found a good link to a manual. I have recently retired from the Navy after 28+ years active duty and am trying to spend as much time in my shop as I did before I...
  9. General Routing
    I just got a craftsman router crafter at a yard sale. Most everything is there except the follower and templates. Can I make these parts? Any advice or comments would be appreciated.
  10. Jigs and Fixtures
    I need one of the 2 inch plastic pulleys: Sears part #29LD-129 (It's part #15 on the manual's parts diagram). Terrible picture attached . . . Any ideas?
  11. New Member Introductions
    Hi Guys! I found this forum while searching for information on the Sears (or any other brand if they exist??) Router Crafter. Any help would be really appreciated. Since they don't seem to be available now, I would consider building one if I can find some plans to use as a guide. I...
  12. New Member Introductions
    Just getting back into woodworking now retired used to have a router crafter but stolen with other tools trying to find one or similar tool anyone help. I live in UK near Severn Bridge Welsh side if any one in my area. Regards Chris
  13. General Routing
    Hi. My name is Pat. I'm a novice woodworker with quite a few tools and not a lot of time to get things done with them. In other words, I'm like 90% of you out there. I'm looking for a PDF of the instruction manual and pictorial samples sheet for the Sears router Crafter if anyone knows of any...
  14. Tools and Woodworking
    I have a Sears Router Crafter Model Number 720-25250 that I purchased new years ago. It has been sitting around the workshop never used. I found the original manual, templates and such that came with it. It has some rust on the chrome posts where the router transport table has been sitting...
1-14 of 14 Results