Router Forums banner

1 - 5 of 5 Posts

·
Registered
Joined
·
2 Posts
Discussion Starter #1
We are selling our Velox CNC table. Machine has very low use. It was used for a laser scanning (metrology) project (never used with a spindle/router). The Velox is in a turn-key state and ready to run, just add router. Details below. Feel free to get in touch with any questions or if you wish to view the machine. Thanks.

$8,000 + ship or local pick-up. Located 46038.

Velox CNC Table Model: VR-2525
25” x 25” x 11” (Upgraded Z-Axis, 11” Travel w/ 9” Clearance)

Machine Specifications:
20MM UNSUPPORTED LINEAR SHAFTS ON THE Z AXIS.
16MM SUPPORTED CYLINDER LINEAR RAILS ON X AND Y AXIS.

X AXIS 1 QTY 5/8 DIAMETER LEADSCREW -- 2 STARTS, 1/4""
TRAVEL PER TURN.
Y AXIS 2 QTY 5/8 DIAMETER LEADSCREW -- 2 STARTS, 1/4""
TRAVEL PER TURN.
Z AXIS 1 QTY 1/2 DIAMETER LEADSCREW -- 1 START, 1/10""
TRAVEL PER TURN.
DUAL EXTERIOR DRIVES ON Y AXIS.
4 LEADSCREWS
4 LEADSCREW NUTS
4 NEMA 23 MOTOR MOUNT BLOCKS.
4 HOME SWITCHES
**FREE REMOTE TECH SUPPORT FOR THE LIFE OF THE MACHINE.

2525-AL-TOP
ALUMINUM TABLE TOP T-SLOTTED. (SECTIONAL TOP. EACH IS
0.750" THICK, 6" WIDE PER..SECTION. EACH T-SLOT IS 2"
APART, T-SLOT STARTS 1" FROM THE EDGE.)

TOOL-ROTARY-INDEXER
4TH AXIS ROTARY TABLE. INCLUDES CUSTOM VELOX ROTARY
INDEXER STAND, NEMA 23 MOTOR MOUNT, 4 JAW SELF-CENTERING CHUCK

TOOL-ROTARY-PLATE-10
10" Diameter Laser Engraving Rotary Table Tooling Plate. MODEL 3727-LAZ.

VR-ZA1100QR-9IC-UPGRADE
VR-SERIES Z-AXIS UPGRADE TO 11" TRAVEL WITH AN
EXTENDED 9" MACHINE CLEARANCE

Controls:
NEMA Box
Toroidal Power Supply
Allen-Bradley & TDK Power Supplies
Optional Encoder Board w/ Encoders
Ethernet Central Switch
HI-CON Integra Controller
P4-S CNC MPG Pendant (USB)
MACH 4 Hobby License
KL8060 Digital Bipolar Stepper Motor Driver 24-80VDC 6A – 32 bit DSP Based (Quantity 5)
NEMA23 280oz/in 2.8A 1/4″ Dual Shaft Stepper Motor (KL23H276-28-4B) (Quantity 3, X-axis, Z-axis, Rotary-axis
NEMA23 382oz/in 3.0A Stepper Motor 1/4 Dual shaft (KL23H2100-30-4B) (Quantity 2, Dual Y-axis)
 

Attachments

·
Retired Moderator
Joined
·
16,385 Posts
Hard to say. The last time he was on the forum was May 31, 2017.
 

·
Registered
Joined
·
121 Posts
Yeah, you should check the date before even asking that question. I am sure it was sold years ago, if not and he answers (I doubt it) surely it would be a scam. Just saying.

Not sure I would ever buy from anyone that does not have at least some feedback, or at least a consistent showing at any forum. Rather than a single post, and go routine.
 

·
Registered
Joined
·
2 Posts
Discussion Starter #5
Sorry I missed these posts, for some reason notifications were being filtered (although I didn't receive any PMs). We ended up donating it to the local IoT lab (Fishers, IN).

Just a lurker, not a scammer. :)

-Regards
 
1 - 5 of 5 Posts
Top