“Yankee” Tool Set No. 100 - Router Forums
 
LinkBack Thread Tools Display Modes
post #1 of 5 (permalink) Old 03-29-2014, 04:40 PM Thread Starter
CGL
Registered User
 
Join Date: Jan 2012
Country: United States
First Name: Chris
Posts: 37
 
Default “Yankee” Tool Set No. 100

Hope everyone is doing well. I purchased a “Yankee” Tool Set No. 100. The instructions inside the box are pretty beat up. I am trying to make a new instruction sheet to look like the original.

The forth paragraph: Chuck and Drill Attachment – (States it came) With 8 drill points XXX - XXX by 64ths, for use in No. 30 Spiral Ratchet Driver. First place the drill point in the chuck and the two together in chuck of screw driver in same manner as bits described above. For drilling, set the shifter for right hand at end of slot toward bit.

I have searched all over the net and cannot read what the 8 drill points are. If anyone should have a set would it be possible to tell me what they are? Thanks in advance. Chris
CGL is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old 03-29-2014, 05:44 PM
Moderation Team
 
Semipro's Avatar
 
Join Date: Mar 2013
Country: United States
First Name: John_*
Posts: 6,674
 
Default

I believe that reads 8 pc,s. 1/16 through 11/64 by 64th,s
Semipro is offline  
post #3 of 5 (permalink) Old 03-29-2014, 05:56 PM
Retired Moderator
 
TwoSkies57's Avatar
 
Join Date: Feb 2009
Country: United States
First Name: Bill
Posts: 6,028
   
Default

Hey Chris,, the best I could find for ya was #'s 1 thru 7..

look near the bottom of the page on this link:

Yankee Tools Checklist

"..... limited only by imagination"

"Just smile and wave boys, smile and wave"
Skipper the Penguin
TwoSkies57 is offline  
Sponsored Links
Advertisement
 
post #4 of 5 (permalink) Old 03-29-2014, 06:01 PM
Retired Moderator
 
TwoSkies57's Avatar
 
Join Date: Feb 2009
Country: United States
First Name: Bill
Posts: 6,028
   
Default

Correction.... John got it right on the money....

8 pc,s. 1/16 through 11/64 by 64th,s

supersize the pic to read the specs..

"Yankee" Tool Set No 100 Complete Set w 3 Yankee Push Drill Point Set RARE | eBay
Attached Thumbnails
Click image for larger version

Name:	100.jpg
Views:	99
Size:	91.6 KB
ID:	70043  


"..... limited only by imagination"

"Just smile and wave boys, smile and wave"
Skipper the Penguin

Last edited by TwoSkies57; 03-29-2014 at 06:20 PM.
TwoSkies57 is offline  
post #5 of 5 (permalink) Old 03-29-2014, 10:20 PM Thread Starter
CGL
Registered User
 
Join Date: Jan 2012
Country: United States
First Name: Chris
Posts: 37
 
Default

I would like to thank all that replied. The instruction sheet was very clear and sharp. Now I need to fill in the pieces. Ya'll are great with your help. Chris
CGL is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Router Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Tool Review Guidelines ~ READ BEFORE POSTING Mark Tool Reviews 5 01-18-2020 09:11 AM
Craftsman v. Delta Tablesaws Thowie70 Tools and Woodworking 22 02-24-2014 10:12 PM
Will a Dremel router attachment fit a 100 series tool? Timberline General Routing 2 11-22-2011 11:51 AM
Tambor door router bit set zarpman Router Bits - Types and Usage 0 11-01-2011 07:41 PM
Finally Got The Gifkins Set Up..... challagan Jigs and Fixtures 25 03-23-2007 10:07 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome