Router Forums banner

Gluing End Grain

5K views 6 replies 5 participants last post by  DesertRatTom 
#1 ·
It seems axiomatic that gluing end grain to end grain is not recommended since doing so does not result in a strong joint. Last weekend, I glued a mitered 1x2 end grain to a mitered 1x2 end grain. After the glue dried, I realized that I made a mistake that required me to separate the two pieces. There was no way that I could pull the two pieces apart. I had to cut into the miter with my SCMS.

Bonus question: In those cases where you do glue the end grain, is the joint stronger if the surface of the end grain is sanded or planed smoother than it would be with just the SCMS cut? All of the wood I use is pine, if that matters.
 
#2 ·
over time that joint could very well fail for no other reason than bond failure..
miter normally and then size the surfaces ...

sizing....

When machining a low density wood (softwoods or hardwoods) or a medium to dense hardwood with substantial amounts of reaction wood, wood fibers may be so weak that they are pushed over instead of cut off. This is especially obvious when sanding--the wood develops very fine "peach fuzz." Although this may be the effect of dull sandpaper or a dull knife, it can often be remedied with glue size. Glue size is used to stiffen and strengthen wood fibers so that they can easily be sanded or lightly planed off.

Glue size is also applied to the porous edges of particle and fiber boards to prevent over-absorption of glues and finishes. This helps fill the grain and give the wood more even coloration and surface quality.

Because many of the materials used for glue size become soft and will flow when heated, it is necessary to avoid high temperatures caused by the friction of aggressive sanding. It is also important to keep the temperature controlled during curing of the finishes.

Most of the time, commercial glue size formulas are better than homemade. Glue size is most commonly made of a watered-down, water-based, PVA adhesive. If you do plan to make your own, try something on the order of 10 parts (or a little less) water to one part white glue. Keep experimenting if this doesn't work out right (it will vary with species). ........
 
#3 · (Edited)
I've never heard of glue sizing. It makes sense, though. Here's a post from Titebond that I just found on the topic.

Get good results gluing end grain joints.
Although good joint design minimizes the need for gluing end grain, sometimes end grain joints are unavoidable. The strength of end grain joints can be improved if the "open" end grain is first sized. A sizing mixture may be made by mixing one part to two parts water to one part glue. Place the sizing mixture on the end grain. Let it soak in for no more than two minutes, and then continue with a regular application of glue.

And here's something else from the website that never occurred to me.

Prevent sunken joints in your projects.
Water-based wood glues such as Titebond Original or Titebond II build strength in a joint as they lose moisture into the surrounding wood. This moisture causes the wood on both sides of the bondline to swell slightly. If the project is planed or sanded before this swelling disappears, the high moisture wood near the joint will continue to dry and will shrink slightly compared to the rest of the wood. Allow your project to dry for several days before sanding or planing.
 
#4 ·
Sanding fills the grain preventing glue from soaking in. The number one reason for end grain joint failure is glue starvation from too much glue being sucked into the grain to leave enough for a proper bond at the joint. That's what the sizing fixes but I usually just put the glue on both pieces and wait a few minutes and then add some more on and wait a few more minutes and then join them together.
 
#5 ·
I usually just put the glue on both pieces and wait a few minutes and then add some more on and wait a few more minutes and then join them together.
That's what I did. Maybe that's why the joint appeared to be so strong.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top